|
Fotos y especificaciones Sub-Zero 430/O |
Resumen del manual
Follow the National Electrical Code and local codes and ordinances when installing the receptacle. For location of the electrical supply, refer to the Installation Specifications illustration. IMPORTANT NOTE: A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation. Do not use an extension cord or two- prong adapter. Electrical ground is required on this appliance. HOME ALARM SYSTEM If a home alarm system is to be used, refer to Home Alarm Connections on page 28. In addition to operating power, the installer may also be required to supply a home automation system lead to the unit. This is for a low- voltage, low-current signal similar to door and window sensor signals. Common, normally open and normally closed contact configurations are provided. Three 1/4" (6) female spade connectors are located in the compressor compartment and are accessible behind the grille on Model 430. A minimum of 36" (914) of lead wire should be provided for each contact, exiting the back wall near the electrical outlet. UNPACKING AND MOVING Uncrate the unit, remove its wood base and discard the shipping bolts that hold the wood base to the bottom of the unit. Remove all packing materials and tape. IMPORTANT NOTE: Do not discard the kickplate, anti-tip blocking kit and hardware. These items will be needed for the installation. All roller-assembly wine shelves should be removed to reduce weight and prevent them from rolling. To remove, pull the shelf out to its full extension, gently and evenly lift up on both sides of the front of the shelf and remove. Reverse the procedure to reinstall the shelf. Retract the front leveling legs to allow you to move the unit more easily during installation. You will extend the leveling legs when the unit is in its final position to reduce the possibility of the unit tipping forward. Use an appliance dolly to move the unit. Remove the drain pan from the base of the unit to avoid damage to the drain pan, and allow for proper placement of the appliance dolly. Before moving the Wine Storage unit in to position, protect any finished flooring with appropriate materials, secure the door closed and remove the grille. MODEL 430 Dimensions in parentheses are in millimeters unless otherwise specified. MODEL 430 INSTALLATION INSTRUCTIONS MODEL 430 GRILLE REMOVAL ANTI-TIP BLOCKING KIT In order to prevent damage to the grille and to access the power cord, the top grille assembly should be removed prior to moving the unit. Framed grille: Remove three counter-sunk grille screws at the bottom of the grille and cut the red nylon shipping strap. NOTE: Grille screws are accessed with the door open. Then tilt the grille forward and release the springs from behind the grille. Refer to illustration 1 below. Overlay panel grille: First, remove the inner grille panel assembly as shown in illustration 2 below. Lift up, then pull out at the bottom, pull the top section down and out of the top key slot. Remove the four mounting screws that hold the outer grille panel assembly to the top compartment. Refer to illustration 3. To prevent the unit from tipping forward and provide a stable installation, the unit must be secured in place with an anti-tip blocking device. An anti-tip blocking kit (wood block and hardware) is provided with the Model 430. If there is a solid soffit above the unit with clearance between the unit and the soffit of 1" (25) or less, you won't need to block the unit. For installations with clearances of more than 1" (25), you must install the anti-tip blocking kit, to prevent tipover in case several loaded wine shelves are extended at the same time. Locate and mark two wall studs against the wall where the unit will be installed. Then locate the proper height to clear the unit. The space between the unit top and the bottom of the wood block must not be more than 1/4" (6). Position the wood block over the unit and use the screws and ‘L‘ brackets to lock it in place. Make sure the screws extend a minimum of 7/8" (22) into each of the two wall studs. The wood block must be positioned securely and must extend at least 3" (76) over the unit. Refer to illustration 5 on page 27. Using the front and rear leveling legs, raise the unit until it makes contact with the wood block. See Level the Unit on page 27. Grille Springs Grille Screws (inside door) Inner Grille Panel Assembly 1 2 3 1 2 3 Panel Grille Frame Soffit 1"(25) Illus. 1 Illus. 2 Illus. 3 Illus. 4 MODEL 430 INSTALLATION INSTRUCTIONS LOCK INSTALLATION IMPORTANT NOTE: If you are adding an accessory lock kit to your Wine Storage unit, it should be installed before you position the unit. Installation instructions are included with the lock kit. For Model 430, the lock is attached to the bottom of the metal door frame. The decorative door panel is not involved in the installation or operation of the lock. The catch portion of the lock is attached to the bottom of the appliance cabinet in pre-punched holes. When insta...
Otros modelos de este manual:Dispensers - 424/O (575.93 kb)
Dispensers - 430/F (575.93 kb)