Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Install a new seat cup, making sure the knob on the stem is fully inserted into the pocket of the seat cup, and the skirt of the seat cup is fully inserted into the bonnet Reassemble in reverse order. IMPORTANT: When replacing heating element, also replace seal gaskets. NOTE: Any abrasion or roughness on the flat end of the seat cup will require replacing the seat cup: 11 SERVICING INSTRUCTIONS (continued) SERVICING INSTRUCTIONS (continued) CAUTION CHEMICAL BURN HAZARD Deliming chemicals are caustic. Wear appropriate protective gloves and goggles during this procedure. Never siphon deliming chemicals or solutions by mouth. This operation should only be performed by qualified and experienced service personnel. IMPORTANT: DO NOT spill, splash or pour water or deliming solution into or over any internal component other than the inside of the water tank. IMPORTANT: DO NOT allow any internal components to come into contact with the deliming solution. Take care to keep all internal components dry. NOTE: Repeat steps 4 thru 5 as required to remove all scale and lime build-up. NOTE: Normally, silicone hoses do not need to be delimed. Should deliming hoses become necessary, Bloomfield recommends replacing the hoses PROCEDURE: Delime the Water Tank PRECAUTIONS: Disconnect dispenser from electric power. Allow dispenser to cool. FREQUENCY: As required (dispenser slow to heat) TOOLS: Deliming Solution Protective Gloves, Goggles & Apron Mild Detergent, Clean Soft Cloth or Sponge Bristle Brush, Bottle Brush Large Sink (or other appropriate work area) 1. Unplug power cord. Turn off the water shut-off valve and disconnect the water supply line from the inlet fitting. 2. Remove the tank lid assembly as detailed on page 10. 3. Using the drain tube, drain all water from water tank. When finished, be sure drain tube clamp is secured. 4. Mix 2 gallons of deliming solution according to the manufacturer’s directions. Carefully pour the deliming solution into the water tank. Lower the lid assembly back onto the tank. Allow to sit for 30 minutes, or as directed by the manufacturer. 5. At end of soaking period, remove lid assembly from tank. Thoroughly rinse internal components of lid assembly with clear water. Using a stiff bristle brush, scrub the heating element to remove lime and calcium build-up. Rinse with clean water. Store lid assembly in a safe location. 6. Drain the water tank. Using a stiff bristle brush, scrub the interior of the water tank to remove lime and calcium buildup. Rinse with clean water. 7. Reassemble the tank lid to the water tank. Make sure the gasket is properly in place. Reinstall wiring to heating element and thermostat. Reinstall fill and vent tubes. 8. Reconnect water supply. Plug in power cord. 9. Allow dispenser to fill, then drain. Repeat three times. 10. Press tank heater switch "ON". When ready light glows, dispenser is ready to use. 712 76580 Owners Manual Hot Water Dispenser 12 712 76580 Owners Manual Hot Water Dispenser EXPLODED VIEWS AND PARTS LISTS SERVICE KITS FAUCET REPAIR KITS 84686 Faucet & Shank Complete 8700-25 L Seat Cup (only) SOLENOID REPAIR KITS 83612 Solenoid Complete, Single 120V (1222, 1222CA) 83760 Solenoid Complete, Single 240V (1225, 1226) 85218 Inlet Fitting Kit (includes cap, fitting, washer & screen) 85219 Inlet Strainer (only) 13 EXPLODED VIEW & PARTS LIST 14 NOTE: Model 1225/1226 shown. Model 1222/1222CA is similar. 712 76580 Owners Manual Hot Water Dispenser EXPLODED VIEW & PARTS LIST (continued) ITEM DESCRIPTION 1222 P/N 1222CA P/N 1225 P/N 1226 P/N 1 WRAP, BODY 2 TANK ASSY 3 PANEL, TOP BACK 4 PLUG, BUTTON 7/8" 8705-36 8705-36 8705-36 8705-36 SUPPORT, TANK 6 LIGHT, PILOT GREEN 8718-31 8718-31 8718-31 8718-31 7 LABEL, HW DISPENSER 8 LIGHT, PILOT AMBER 61178 61178 61178 61178 9 CONTROL, LOW WATER, 120V CONTROL, LOW WATER, 240V 66604 66604 503141 503141 SPACER, NYLON 11 PANEL, REAR LOWER 12 SOLENOID, SINGLE 120V SOLENOID SINGLE 240V 83612 83612 85760 85760 13 DOOR, ACCESS 85089 85089 85089 85089 14 SWITCH, ROCKER 250V 505295 505295 502541 502541 STRAIN RELIEF 50789 50789 16 CORDSET 20141 20141 17 FAUCET & SHANK ASSY 84686 84686 84686 84686 18 ELBOW, OUTLET 8043-11 8043-11 8043-11 8043-11 19 TUBE, 3/8 x 3/4" LONG 85609 85609 85609 85609 TUBE, SILICONE .312 DI x 25" LONG 83540 83540 83540 83540 21 TUBE, BRAIDED .312 ID x 21" LONG 86237 86237 86237 86237 22 CLAMP, HOSE SHUT OFF 86564 86564 86564 86564 23 GASKET, HEATING ELEMENT 8043-30 8043-30 8043-30 8043-30 24 GASKET, TANK HEATING ELEMENT, 120V 1800W 86524 HEATING ELEMENT, 120V 1500W 86571 HEATING ELEMENT 208V 4000W 86721 nser HEATING ELEMENT 240V 4000W 86720 26ispeLID ASSY 27er DTHERMOSTAT, TEMPERATURE CONTROL 86280 86280 86280 86280 28WatTUBE, TANK FILL 86237 86237 86237 86237 29Hot PROBE, LIQUID LEVEL 85746 85746 85746 85746 FOOT, 1/2" HIGH BLACK RUBBER 505148 505148 21657 21657 31Owners Manual THERMOSTAT, HI-LIMIT SAFETY 8043-83 8043-83 8552-50 8552-50 32 GROMMET, 3/8 ID 82390 82390 82390 82390 33 SLEEVE, WATER LEVEL PRO...
Otros modelos de este manual:Dispensers - 1225 (805.62 kb)
Dispensers - 1226 (805.62 kb)
Dispensers - 222CA (805.62 kb)