Votos - 4, Puntuación media: 3.5
(
)
)
|
Resumen del manual
INSTALLATION READ THIS CAREFULLY BEFORE STARTING THE INSTALLATION CAUTION: Equipment REFER TO EXPLODED VIEWS PAGE 9 FOR COMPONENT Electrical Damage NAMES/NUMBERS DO NOT plug in or energize this appliance until all Installation Instructions are read and followed. Damage to the Brewer will occur if these instructions are not followed. CAUTION: Unstable Equipment Hazard It is very important for safety and for proper operation that the warmer is level and stable when standing in its final operating position. Provided non-skid feet must be installed at each corner of the unit. Do not install this appliance if the feet are missing or damaged. WARNING ELECTRIC SHOCK HAZARD: Warmer must be properly grounded to prevent possible shock hazard. Electrical shock will cause death or serious injury. IMPORTANT: Supply power must match nameplate for voltage and phase. Connecting to the wrong voltage will damage the warmer or result in decreased performance. Such damage is not covered by warranty. Unpack the unit. Inspect all components for completeness and condition. Ensure that all packing materials have been removed from the unit. LEVELING THE UNIT Verify that a slip-resistant foot is installed at each corner of the dispenser. Set the warmer in its operating location. Be sure all four feet touch the counter to prevent tipping. ELECTRICIAN’S INSTALLATION INSTRUCTIONS REFER TO ELECTRICAL SPECIFICATIONS -Page 1 Check the nameplate to determine correct electrical service required for the warmer. Models HD8799 and HD8802 dispensers are equipped with a cord and plug. They requires a 115 - 125 volt circuit (50/60 Hz, 2 wire plus ground, with NEMA 5-15R receptacle). IMPORTANT: The ground prong of the plug is part of a system designed to protect you from electrical shock in the event of internal damage. Never cut off the ground prong nor twist a blade to fit an existing receptacle. Contact a licensed electrician to install the proper circuit and receptacle. GROUND PIN NEMA 5-15P NEMA 5-15R PLUG RECEPTACLE 4 PREPARATION Prior to first use, thoroughly clean warmer (see page 6). Be sure faucet handle is "up" and that drip tray is in place under faucet. USE Pour product into warming tank. Using pre-heated product will reduce heat-up time. Model HD8799 utilizes a fixed thermostat to hold product at 140.F (60.C). Model HD8802 thermostat may be adjusted to hold product at 170.F (77.C) maximum. Reinstall tank cover. Plug dispenser into an appropriate electrical receptacle. Turn power switch to ON. When the READY light glows, product is ready to serve: Place an appropriate container under the faucet. Pull the faucet handle to dispense product. Release the handle to stop the flow of product. NIGHTLY CLOSE Turn the power switch to OFF and unplug the dispenser. If required, empty the dispenser and clean. TEMPERATURE ADJUSTMENT (Model HD8802 only) Remove button plug from rear of dispenser to access thermostat. Turn shaft of thermostat to adjust setpoint temperature. Turn the shaft clockwise to increase temperature. Moving the shaft 1/8 turn will change the temperature approximately 10.F. OPERATION CAUTION: Burn Hazard Exposed surfaces of the appliance may be HOT to the touch and can cause burns. NOTE: Product may continue to flow for several seconds after the faucet is released. Do not remove the container until all flow has stopped. IMPORTANT: Your local Health Department can advise whether or not a particular product may be left in the dispenser overnight. IMPORTANT: Temperature adjustment to be performed by authorized personnel only. 5 CLEANING INSTRUCTIONS CAUTION: Electric Shock Hazard Do not submerge or immerse dispenser in water. CAUTION: Burn Hazard This procedure requires the use of very hot water. Wear protective gloves while cleaning the warmer. Very hot water can cause burns. IMPORTANT: DO NOT use steel wool, sharp objects, or caustic, abrasive or chlorinated cleansers to clean the dispenser. PROCEDURE: Clean Heated Dispenser PRECAUTIONS: Disconnect dispenser from electric power. Drain product and allow dispenser to cool. FREQUENCY: Daily or after draining product from dispenser TOOLS: Mild Detergent, Clean Soft Cloth or Sponge Long Handle Bristle Brush 1. Disconnect warmer from electric power. Drain product and allow warmer to cool before cleaning. 2. Fill warmer with very hot water. 3. Place an appropriate container under the faucet. Use a long handle bristle brush to stir the water while draining the hot water from the warmer. 4. Wipe the warmer inside and out with a soft cloth or sponge dampened with water and mild detergent. 5. Rinse the warmer inside and out with a soft cloth or sponge dampened with clean water. 6. Wipe the tank cover with a soft cloth or sponge dampened with water and mild detergent. Rinse with clean water. 7. If necessary, clean the faucet and drip tray (see page 8). 8. Allow all components to air dry, then reassemble. Procedure is complete 6 TROUBLESHOOTING SUGGESTIONS SYMPTOM POSSIBLE CAUSE SUGGESTED REME...
Otros modelos de este manual:Dispensers - HD8802 (736.81 kb)