Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
In the unlikely event of experiencing any difficulties, call: BRITA Customer Careline: 0844 7424800 for expert advice (Monday - Friday 8.30am - 5.30pm. Local rates apply) Also remember to REGISTER your chiller online or by the enclosed card QUICK SET-UP GUIDE Detailed instructions are included but for a quick set up, follow these key tips: 1 Before use, make sure water tanks are thoroughly washed and that water is flushed through the entire chiller system (the removable bottom plug will aid this). See page 4 for full instructions. 2 For optimum taste and filtration speed, ensure your BRITA Maxtra cartridge is properly prepared before insertion into the top water tank. See page 5 for full instructions. 3 When positioning the Aqua Fountain ensure it has a minimum of 15cm clearance for the ventillation slots at the back for efficient air circulation and maximum water cooling performance. See page 4 for full instructions. 4 Use a jug to fill the tanks with cold water and take care not to spill down the tank sides or fill beyond the MAX FILL LEVEL. Add the water until all tanks are full. To prevent air locks in the internal chilled water tank, depress the dispense lever until the water flows out. See page 6 for full instructions. 5 Keep your Aqua Fountain out of direct sunlight and away from any heat sources. See page 6 for full instructions. 6 Cooling time will vary depending on your ambient and water temperature. See page 6 for full instructions. 2 FEATURES FEATURES Fig 1 qwertuyioas 1. BRITA Memo - cartridge exchange indicator 2. Upper water tank cover 3. Hinged lid 4. 1 litre upper water tank 5. 2 litre filtered water tank 6. ON/OFF switch 7. Red power on indicator 8. Chilled water indicator 9. Water dispenser lever 10. 1 litre chilled filtered water tank 11. BRITA MAXTRA water filter 3 BEFORE USING YOUR WATER FILTER/CHILLER Before using your water filter/chiller for the first time, it is recommended that the unit is flushed through with fresh water. Please ensure that you read the following instructions before flushing your water filter/chiller several times. 1. Remove your water filter/chiller carefully from the box. You may wish to store the packaging for future use. 2. Check the contents: • Water filter/chiller • BRITA MAXTRA water filter cartridge • User guide • BRITA brochure • BRITA registration card 3. Wash the clear plastic lid, upper and filtered water tanks in warm soapy water, rinse and dry thoroughly. 4. Reassemble the tanks as shown below. Upper water tank cover Upper water tank Filtered water tank Chilled and filtered water tank 5. Position the water filter/chiller on a stable flat surface, close to a mains power socket, not in direct sunlight and out of the reach of children. 6. Make sure that there is sufficient space around the water filter/chiller to allow the heat extracted during the chilling process to dissipate. Leave a gap of at least 15 cm between the ventilation slots on the rear of the chiller and any wall or surface. Do not plug the unit in or install the filter cartridge yet. 7. Lift the hinged lid and using a suitable jug, pour 2 litres of clean water into the tank. Place a glass under the dispenser and push the dispensing lever back to drain all of the water. It may take some time for the water to initially flow through. 8. Repeat this process one more time. 4 PREPARING THE FILTER CARTRIDGE PREPARING THE FILTER CARTRIDGE 1. Remove the cartridge from its wrapping (it is normal for the cartridge to appear moist during storage - this is simply condensation). 2. Immerse the cartridge in cold water and agitate gently to remove any air bubbles. . ..... NOTE There is no need to pre-soak this cartridge before use. 3. Remove the lid from the upper water tank. 4. Insert the filter cartridge into the water tank as shown below. Push it firmly into place. When correctly fitted, the cartridge should remain in place when the tank is turned upside down. 5 1. Place the upper tank on a suitable bowl or jug. Fill with cold tap water up to the MAX FILL LEVEL mark on the upper water tank and allow the water to filter through. Maximum fill level mark Discard the first two fillings. These first two fillings are used to flush the filter cartridge. Place the upper tank back into the unit. 2. Replace the upper water tank lid. 3. Press and hold the START button on the BRITA Memo on the lid until all of the bars on the display appear and flash twice, see “Using the Memo function” on page 8. . ..... NOTE When it is time to replace the cartridge after 4 weeks use, simply lift the ring pull handle on top of the cartridge to remove. The cartridge may be disposed of in household waste or contact the BRITA-Care customer service for advice on recycling schemes. USING YOURWATERFILTER/CHILLER USING YOURWATERFILTER/CHILLER 1. Lift the hinged lid and using a suitable jug, carefully pour water into the tank up to the MAX FILL LEVEL. This may take some time due to the action of the filter. 2. Keep addi...
Otros modelos de este manual:Dispensers - AF5 (1.29 mb)