Votos - 3, Puntuación media: 3
(
)
)
|
Resumen del manual
It can be purchased direct from BUNN-O-MATIC (part number 32759.10_ _ [see Illustrated Parts Catalog for complete part number.]) BUNN-O-MATIC does not recommend the use of saddle valves to install the dispenser. The size and shape of the hole(s) made in the supply line(s) by saddle valves may restrict water flow. Note-A water strainer (Bunn-O-Matic part number 23720.1000) should be installed in line, prior to the flexible water line. This equipment must be installed to comply with the Basic Plumbing Code of the Building Officials and Code Administrators International, Inc. (BOCA) and the Food Service Sanitation Manual of the Food and Drug Administration (FDA). PLUMBING HOOKUP CAUTION: The dispenser must be disconnected from the power source throughout the plumbing hookup. All plumbing connections are located behind the dispenser’s splash panel. Water lines may enter the dispenser through the access holes in either the bottom panel or the rear panel of the dispenser. To access plumbing connections: remove the drip tray assembly; remove the two screws securing the splash panel to the dispenser; lower the splash panel from the front of the dispenser. Refer to FIG 2 for proper water hookup. Alternate Connection (When Hot Water source is not available) RINSE WATER CONNECTION RINSE WATER CONNECTION Cold Water Connection Cold Water Connection Hot Water Rinse Connection MAIN WATER CONNECTION MAIN WATER CONNECTION Hot Water connection (See Caution) 3/8" x 3/8" x 3/8" Barb Tee B.O.M. PN 32750.0000 (may be installed internal or external to the dispenser) FIG 2 Plumbing Connections P2265.70 5 33496 011101 P2262.60 FIG 3 Refrigeration Switch A B C P2263 FIG 4 Sanitize Switch & Water Valves A. Sanitize Switch B. Water Bath Valve C. Main Water Valve OPERATING CONTROLS Refrigeration Switch The refrigeration switch is located on the top of the dispenser near the left rear corner. This switch controls power to the compressor and the condenser fan motor. Sanitize Switch The sanitize switch is located behind the drip tray in the lower left corner of the chassis. The drip tray can be removed to provide easy access to the switch. The sanitize switch is used to enter and exit the sanitize mode and to initiate the sanitize automatic cycle. Refer to Weekly Sanitizing in the Cleaning section for detailed instructions on the use of this switch. Water Bath and Main Water Valves These valves are manually operated and are located above the drip tray, behind the splash panel. The drip tray and splash panel must be removed to gain access to the valves. The upper (small) one is the water bath valve and the lower (large) one is the main water valve. Refer to the Initial Fill section for detailed instructions on the use of these valves. 33496 122200 6 OPERATING CONTROLS (cont.) C C A A AAB FIG 5 Press and Hold Models A. Product Dispense Switch Pressing and holding switch will initiate product flow from the respective nozzle; releasing the switch will stop the flow. B. Chilled Water Dispense Switch Pressing and holding switch will initiate chilled water flow from the nozzle; releasing the switch will stop the flow. C. Hidden Switch These switches are used to access, change and exit the dispenser program mode. D D D DCCB EE EE FIG 6 Portion Control Models B. Chilled Water Dispense Switch Pressing and holding switch will initiate chilled water flow from the nozzle; releasing the switch will stop the flow. C. Hidden Switch These switches are used to access, change and exit the dispenser program mode. D. Product Dispense Switch Momentarily pressing and releasing one of the switches will initiate a timed dispense. Each station has three different timed dispenses which are preset at the factory. Refer to DISPENSER USE section for preset volumes and adjustment procedures. E. Plus/Stop Switch This switch can be used to “top-off” a beverage. Pressing and holding switch will initiate product flow from the respective nozzle; releasing the switch will stop the flow. Momentarily pressing this switch during a timed dispense will stop the flow. 33496 122200 7 INITIAL FILL CAUTION: The dispenser must be disconnected from the power source throughout the initial fill except when specified in the instructions. 1. Remove drip tray assembly and splash panel from the dispenser. 2. Pull the overflow tube from its retaining clip and place the end into an empty 64 fluid ounce (2 liter) container. 3. Ensure that the Main Water Valve and the Water Bath Valve Fig 4, are turned off (handles positioned at 6 o’clock and 12 o’clock, respectively,) and that the Refrigeration Switch Fig 3, is in the OFF (rear) position. 4. Turn on the water supply. 5. While observing the water bath sight gauge (the clear tube located just to the left of the plumbing connections,) begin filling the water bath by rotating the handle of the Water Bath Valve counterclockwise to the 9 o’clock position. 6. When the water level in the sight gauge comes within 1 inch (25.4 mm) of the clear plastic te...