Votos - 1, Puntuación media: 4
(
)
)
|
Resumen del manual
Grindmaster Corporation Canton Plant 480 Neponset St. Canton, MA 02021 USA Phone (502) 425-4776 (800) 695-4500 Fax (502) 425-4664 © Grindmaster Corporation, 2000 1103 Form# CC-399-04 PRINTED IN THE USA Part# 90381 Introduction and Warnings This instruction manual is an important part of this Granita machine and must be kept for future reference. Carefully read the warnings contained in this instruction manual before installing and operating this Granita machine. Instructions For Machine Transport NOTE: Refrigeration equipment must remain upright to avoid damage to the compressor In order to prevent the oil contained in the compressor from flowing into the cooling circuit, it is necessary to always ship, carry, store and handle this Granita machine in an upright position, following the instructions located on the packaging. Never ship, carry, store or handle unit on its side. Installation 1.) Cut banding straps from box and lift the box off the machine (see fig. A). 2.) Positioning the machine • The machine must be well ventilated. Leave an 8” (20 cm) clearance on the sides and back of the machine to allow proper ventilation. Installation of the machine near a heat source should be avoided. Some heat sources you should avoid locating this unit too close to are ovens, coffee machines, cold or frozen beverage dispensers or ice machines (equipment with compressors that expel hot air through its vents). Machines should also not be positioned near dust producing units such as a Powdered Cappuccino or Cocoa dispenser. A room temperature between 59°F (15°C) and 77°F (25°C) is recommended (see fig. B). • The lit merchandising covers are reversible (front to back) depending upon the needs of the operator (see fig. B). 3.) Remove Shipping Pin ! Attention: Shipping pin attached to tag located behind (Figure B) each bowl must be removed before starting machines. • Lift up and remove rear back-lit merchandiser panel (see fig. C). NOTE: Some units may have dual rear back-lit merchandiser panels, these function in the same manner as the single panel rear merchandisers. • Pull out each pin attached to each tag (see fig. D) • Replace rear back-lit merchandiser panel (see fig. E). (Figure A) 8" (20 cm) (Figure C) (Figure E) (Figure D) Page 2 G & MG Series Granita Machine Installation (cont.) 4.) Installing the Top Lid Merchandiser (requires Phillips head screwdriver) • Unplug the cord to the lid and remove the lid from the machine. • On top of the cover, remove the 4 hole plugs over the front (2) screws, middle (near rocker switch) and back screws then remove these 4 screws with a Phillips head screwdriver. Remove the black top part of the cover (Figure E) from the clear plastic base. (see fig. E) • Slide the merchandiser header around the outside edge of the lid’s clear plastic base. Position bottom edge of header in grooved area. (see fig. F) • Reassemble the black top cover onto the clear plastic base. The top edge of header should slide into black top cover grooved area. (see fig. F) Replace screws. Replace hole plugs (the angled plugs goes in the rear hole, and the two large plugs go in the two front holes and the small plug goes in the center hole by the rocker switches). (Figure F) • Replace assembled lid on machine and reattach cord. 5. Installing the Rear Back-lit Merchandiser • To remove any existing artwork, bend or pinch the middle of the back-lit merchandiser and pull it from the rear merchandising display casing. (see fig. G) (Figure G) • To insert new art, slide the left corner edges into the left top and bottom casing edges. (see fig. H) • Slightly bend art and insert the right side of art into the right top and bottom casing edges. (see fig. H) • Smooth out art until all edges are properly inserted into the casing. (Figure H) Connection To Main Power Supply ! Attention: Before inserting the plug into the electrical outlet, carefully read the following precautions. • The electrical safety of this Granita machine can only be achieved if the machine is properly connected to an appropriate grounded, electrical receptacle that is in compliance with current national safety standards. Therefore, the manufacturer cannot be held responsible for damage and/or injury caused by failure to connect the unit to an appropriate source of power. • For a safe and correct installation, connect the unit to a dedicated outlet. • Do not alter the cord or plug in any way. ! Attention: Altering the cord or plug will void the warranty. • The entire length of the power supply cord must not, in any way, be compressed (bent or bunched together) nor may extension cords be used. • Do not obstruct the ventilation and heat dispersion grill vents on the side and rear panels of the unit. An insufficient ventilation process may reduce the efficiency of the machine, causing it to function inadequately, and cause serious damage to the machine. A minimum of eight inches (20cm) clearance is necessary on each side and behind the ...