Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
Check dispenser and icemaker operation. 16. Sanitize icemaker according to instructions in icemaker manual. Discard ice made during sanitizing process. 17. Turn off icemaker bin signal switch. 18. Remove dispenser hopper lid; clean and sanitize dispenser according to instructions beginning on page 16. 19. Turn icemaker bin signal switch on and replace front covers, securing with screws. 8 Installing countertop dispensers ! Dispensers with top mount icemakers cannot be mounted on legs.They must be bolted to counter. Use gloves when lifting icemaker to protect hands from sheet metal edges. 1. Position dispenser in desired location, mark dispenser outline on counter and remove dispenser. 2. Drill four 3/8" (5mm) holes in counter (Fig. 2) to anchor dispenser to counter. Follett countertop dispensers can have any or all utilities run directly through counter or out rear of dispenser. For dispensers with any utilities exiting through counter, make counter cut-out (Fig. 2) 3. If ice transport tube will exit out rear of dispenser, remove ice transport tube knock-out (Fig. 5G) from rear of dispenser. Note: Utility connections can be accessed through front of dispenser by removing stainless steel splash panel, or by removing access panel (Figs. 4, 5) on back of dispenser. 4. If any electric utilities or water line will be connected through rear of dispenser, remove utility knock-out (Figs. 4, 5F) from rear of dispenser and install supplied protective grommet. Fig. 2 – Counter cut-out, all models 21" (533mm) 20.125" (511mm) .44" (11mm) .5" 1.5" (38mm) (127mm) 12.5" .375" holes (317mm) (9.52mm) 16.5" (419mm) .375 (10mm) 6.5" (165mm) 10.5" (267mm) 9" X 14" (227mm x 356mm) drain pan cut-out Fig. 3 – Top view, dispenser plumbing connections countertop drain pan (L) 3/4" FPT dispenser drain (K) alternate 3/4" dispenser (drain location) (G) 3/8" FPT water inlet (J) 3/8" FPT condenser water outlet (H) 3/8" FPT condenser water inlet 9 5. If power is to be supplied through counter cut-out, complete steps 6-9. If power is to be supplied through rear of dispenser, proceed to step 10. 6. Temporarily remove rear access panel (Figs. 4 and 5) from rear of dispenser. 7. Loosen junction box mounting screws. Lift junction box and power cord up until cord and mounting screws clear notches on rear panel of dispenser. Remove Phillips head screws from right side of junction box. 8. Rotate junction box 90 degrees so that screw holes on right side of junction box align with holes on rear dispenser panel. Resecure junction box to dispenser using Phillips head screws. 9. Place power cord inside dispenser and replace access panel (Figs. 4, 5) to rear of dispenser. Note: For dispensers to be installed with utilities connected through rear of dispenser, it may be easier to make preliminary connections before dispenser is set in place. 10. Apply a thick bead, approximately. 1/4" (6mm) diameter, of NSF listed silicone sealant (Dow-Corning RTV732 or equivalent) 1/4" (6mm) inside marked outline of dispenser. 11. Carefully position dispenser on counter. 12. Remove four screws securing splash panel to front of dispenser and gently lay splash panel on counter. (Water line to solenoid valve can be disconnected from water inlet valve by pushing on ring at end of inlet fitting while pulling on tubing.) 13. Secure dispenser to counter with four 3/8" bolts (supplied by others). 14. Smooth excess sealant around outside of dispenser. 15. Run water supply line from back of dispenser through utility knock-out (Figs. 4, 5F) or up through counter cut-out. Connect water supply line to 3/8" FPT fitting on (Fig. 3G) utility flange at bottom of dispenser. 16. Remove 3/4" drain connection plug from either fitting at rear of dispenser (Fig. 3L) or internal fitting (Fig. 3K), as appropriate. Connect and run a dedicated drain line to wall or floor drain. An air break should be provided. 17. Proceed with either Satellite-fill or top-mounted icemaker connection instructions, as appropriate. Fig. 4 – Rear connections, countertop Fig. 5 – Rear connections, countertop models with integral icemakers models with Satellite-fill icemakers (F) utility connection knock-out 3/4" FPT drain access panel .8" 5.875" (149mm) 14.75" (375mm) 10.5" (267mm) (20mm) 5.875" (149mm) .8" (20mm) 10.5" (267mm) 6.375" (162mm) 14.75" (375mm) (G) ice transport tube knock-out (F) utility connection knock-out 3/4" FPT drain access panel 10 Installing wall mount dispensers 1. Install supplied wall bracket with six 3/8" diameter fasteners as shown in Fig. 7. Note: Three holes are available at each fastening site to allow capture of studs/support within wall. Steps 2 - 3 are required for models with integral icemaker only (25HT400A/W and 50HT400A/W). 2. For models with integral icemaker, use straight edge to position filler strip flush with top edge of wall bracket. 3. Fasten filler strip to wall as shown in Fig. 8. 4. For all models, cut utility hole in wall (Figs. 7 and 8) using wall bracket as template. ...
Otros modelos de este manual:Dispensers - 50 (1.55 mb)