Votos - 5, Puntuación media: 3.4
(
)
)
|
Resumen del manual
2. Pour 1 gallon (4 liters) hot water into drain pan to keep drain lines clear. Recommended weekly cleaning 1. Remove drain pan and grill and wash with Solution A. Rinse thoroughly. 2. Remove nozzles and diffusers from valves, soak for at least 10 minutes in cleaning Solution A, rinse, sanitize with Solution B and reinstall. 3. Pour a solution of one cup (8oz/237ml) household bleach mixed with one gallon (3.8 liters) hot water into drain pan to help prevent algae growth in drain lines. 9 Recommended quarterly cleaning (every 3 months) On push button units, remove dispense switch from dispense chute ! cover before cleaning chute cover. 1. Turn power switch to "OFF" position and remove top from dispenser. 2. Remove ice from storage area. 3. Remove dispense chute cover, chute, auger motor assembly, auger and auger tube (see page 11). 4. Remove drain pan, grill, dispense wheel and cover plate (see page 12). 5. Clean all components and bin storage area with Solution A, rinse thoroughly with clear water and sanitize with Solution B. 6. Remove nozzles and diffusers from valves, soak for at least 10 minutes in cleaning Solution A, rinse, sanitize with Solution B and reinstall. 7. Clean area below wheel and stainless cover plate with Solution A, rinse and sanitize with Solution B. 8. For units with integral ice-water bath beverage cooling only: • Remove side access panel opposite ice tower. • Lower drain tube found on utility connection side of dispenser and drain ice-water bath. • Use a bottle brush to clean coils with Solution A, rinse and sanitize with Solution B. • Reposition water bath drain line in "UP" position so water does not drain out. • Pour Solution A into water bath until it flows out overflow drain. • Turn power ON and push dispense lever or dispense button back in "dispense" position. • Allow pump to run for 2 minutes to clean pump and pump lines. • Turn power OFF. • Drain bath and replace drain tube in "UP" position to avoid siphoning water bath water. Putting unit back in service after quarterly cleaning 1. On units with integral beverage cooling, fill ice-water bath with water until water spills out of bath overflow drain. 2. Reassemble components. 3. For manual load units, fill unit with an approved ice (see caution statement on page 1). 4. For automatic load units with R5A/W (R22 refrigerant) icemakers, turn bin signal switch(es) and dispenser power switch to "ON" position and allow storage area to fill. 5. Push dispense button or lever to test that dispenser is functioning properly. Quarterly cleaning of icemaker system Units equipped with icemakers require cleaning of icemaker system at least every three months, and more often if local water conditions dictate. Failure to clean icemaker system will result in decreased performance and potential damage to icemaker. Refer to Icemaker Operation and Service Manual. 10 Disassembly instructions for periodic cleaning Dispense chute cover removal RH, 8-valve unit 1. Remove top cover. front view 2. Push chute cover up vertically to slip off holding tab. valves chute 3. After clearing tab, pull chute cover forward top cover cover to remove. Dispense mechanism assembly drain pan removal assembly dispense 1. Remove top cover. chute 2. Remove chute cover (see above). 3. Remove auger motor assembly (see above). 4. Remove quick release pins from the ice chutes and gates, then unplug wires from solenoids. 5. Lift dispense mechanism up and off auger tube. Auger and auger tube removal Dispense assembly, top view (see drawing p. 12) (RH unit with bath shown) 1. Remove auger motor and dispense mechanism assembly (see above). ice chute 2. Pull auger upward to clear auger tube. 3. Lift auger tube upward to clear dispenser top. 4. Slide tube and bearing plate through auger tube gasket. solenoid Dispense wheel removal 1. Remove drain pan assembly and bin access cover. 2. Remove center thumbnut and threaded rod on dispense wheel assembly and lift wheel out front pin access opening. Auger motor assembly removal 1. Remove top cover. 2. Remove one thumbnut on rear of motor bracket. 3. Lift motor bracket up and unplug electric quick disconnects. 4. Remove motor assembly. quick release gate quick release pin 11 auger motor (side view) stationery agitator wheel plate motor baffle plate wheel motor mounting plate dispense wheel auger tube auger auger bearing rotating agitator front view Service Disassembly instructions for service requirements only – NOT required for any cleaning procedure. Dispense wheel motor removal (see drawing above) 1. Remove drain pan, bin access cover and dispense wheel. 2. Remove stainless steel baffle plate under dispense wheel. 3. Remove two screws holding wheel motor bracket on bin. 4. Lift plate and motor up. 5. Unplug electric quick disconnects from motor. 6. Lift motor and mounting plate out front access opening. 12 Wiring diagram - Right hand unit Left hand unit L1 BLACK 13 115 VOLTS 24 VOLTS RED -WARM STATUS LIGHTS GREEN - COLD BATH CONTROL B...