Votos - 1, Puntuación media: 4
(
)
)
|
Resumen del manual
R Power Supply (included) Power Supply Adaptor (included) TV outputs (8) Power LED Modulator inputs (2) Antenna/CATV Model 3308 Top View Accessories 2 The 3308 Coaxial Cable Panel is the heart of a multiroom video distribution system. The 3308 connects as many as 8 televisions to cable or antenna, while maintaining compatibility with ChannelPlus video modulators and the ChannelPlus bi-directional IR repeating system. Model 2010 Power Injector wall plate (fits standard Decora) Model 2184 IR Breakout Replaces the power supply adaptor and drives up to four IR emitters. +12 GND LED - + R Satellite receiver Modulator Antenna/CATV Up to 8 TVs LOSS-LESSCOAXPANEL The model 3308 works like a zero-loss splitter! The signals you put on the antenna/CATV input will appear on the outputs at the same power. Typical System R Satellite receiver Modulator Antenna/CATV Up to 8 TVs FREEDOMOFPLACEMENT Put the 3308 coax panel where the coax is: in the attic, in the basement or in the wall of the garage. The single coax from a model 2010 carries power, the RF signals and IR repeating signals. Remote Power Using the Model 2010 Model 2010 Power Injector IMPORTANT: The model 2010 must connect to the port. If the 2010 is not being used, then install a 75 ohm terminator here. Modulator B +Pwr 3 IR EMITTERS POWER 15VDC SYSTEM POWER FROM MODULATOR VIDEO SYSTEM IR EMITTERS POWER 15VDC SYSTEM POWER FROM MODULATOR VIDEO SYSTEM Shielded 75 ohm coax is required. We recommend RG-6. Modulators may be connected to the .A. or .B. ports. MODULATORS INPUTS A B+Pwr OUTPUTS model 3308 Coax Panel To TVs Ant / CATV INPUT R +15Vdc IR Out Gnd For use with model 2100A IR wallplates IR Repeating System IR EMITTERS POWER 15VDC SYSTEM POWER FROM MODULATOR VIDEO SYSTEM Model 2171 IR Emitter Compatible IR Targets Model 2131 Model 2130A Model 2132 With the model 3308, you can also control your video devices from any room in the house. Any or all 8 outputs may be connected to model 2100A wall plates. The wall plates interface with a variety of industry standard IR targets. Direct your IR remote control at the IR target and the 2173 IR emitter will repeat the IR signals in the media center. IR control signals from the bedroom . IR control signals from the bedroom . Are repeated at the media center. Change the DSS channel or pause the VCR from any room. Are repeated at the media 1 1 2 2 Normally, the IR emitters are also connected to Model 2100A wall plates. But, if the coax panel is located in the media center, you may choose to connect the emitters to a model 2184 IR breakout panel. Both examples are shown below. The model 2184 plugs directly into the 3308, replacing the power adaptor cable. The 2184 can drive up to 4 IRemitters. If the coax panel is not located at the media center, you may add a model 2010 remote power wall plate at the media center and connect the 3308 and 2010 with a single coax cable. The model 2010 will power the 3308, drive the IR emitters and deliver any modulator signals to the 3308. In addition, the 2010 has connectors for 2 IR emitters. (The model 2174 IR expansion panel will expand each of these ports to drive up to 4 IRemitters.) Model 2173 Model 2173 Model 2100A Model 2100A Model 2100A Model 2010 Model 2173 Model 2184 Model 2130A Model 2132 Modulators may be connected here. The 2010 must be powered as shown. Model 2010 MUST be connected to the .B. port. More modulators may be connected to the .A. port. Max recommended cable length 150. (Total of these two pieces.) 4 5 POWER LED EMITTER TARGET TO TV POWER LED EMITTER TARGET TO TV POWER LED EMITTER TARGET TO TV IR targets must be connected to a model 2100A wall plate. IR targets must be connected to a model 2100A wall plate. DC block When using IR repeating, only a or may be directly connected to a 3308 output. 2100A DC block Mounting the 3308 The model 3308 should be mounted in a location that is safe and dry. The model 3308 is small enough to be mounted a stud wall. Alternatively, the 3308 may be mounted inside a ChannelPlus IntegratedHomeNetwork enclosure. inside We recommend using only RG-6 coax when wiring a house. Why? Although good RG-59 has only slightly more loss than RG-6, it is harder to find good RG-59. RG-6 is a little more expensive and a little harder to run (because it is thicker). But you will avoid surprises if you stick to RG-6. NOTE: Circuit Breaker Model 2010 Power Injector Note: The model 2010 must connect to this port. Power LED Power LED Power LED The model 2010 and 3308 have built-in circuit breakers. If any of these LEDs are not lit, reset the circuit breaker by disconnecting and reconnecting the power supply. If the system does not reset, look for an installation error. 6 Expanding the 3308: CATV/Ant Model 3308 Model 3308 Model 3308 You may connect up to 8 more 3308s to the outputs of a .master. 3308, for a total of 64 TV outlets. The longest recommended coax run is 150 feet (includes coax from master to secondary unit and from secondary unit to TV). Up to ...