Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
Then press the Ppower button on the projector or the On button on the remote control to turn it back on. Power light and power button are on Projection is in progress. Lights indicating a problem Light state Cause and solution All lights are off The projector is not receiving power. Make sure the power cord is connected securely at both ends. The temperature light flashes orange High-speed cooling is in progress. If the temperature rises further, projection will stop automatically. Make sure there is plenty of space around the projector for ventilation. Clean or replace the air filter if necessary (see page 61). If you are using the projector at an altitude above 4921 feet (1500 meters), turn on High Altitude Mode so the fan can cool the projector properly (see page 52). The temperature The projector is too hot, which turns off the lamp automatically. light is red Let the projector cool for five minutes, then turn it back on. Make sure there is plenty of space around the projector for ventilation. Also, clean or replace the filter if necessary (see page 61). If you are using the projector at an altitude above 4921 feet (1500 meters), turn on High Altitude Mode so the fan can cool the projector properly (see page 52). The lamp light flashes orange The lamp needs to be replaced. The lamp light There is a problem with the lamp. If you just replaced the lamp, flashes red make sure the lamp and its cover are securely installed (see page 63). Turn off the projector and unplug it from the electrical outlet. Wait for the lamp to cool, then remove the lamp and check it for cracks. If the lamp isn’t cracked, reinstall it, plug the projector into an outlet, and turn the power on. If this doesn’t fix the problem, or if the lamp is cracked, contact Epson for assistance (see page 76). Problem Solving 69 Lights indicating a problem Lights indicating a problem Cause and solution The temperature light flashes red There is a fan or sensor problem. Turn off the projector and unplug it from the electrical outlet. Then contact Epson for assistance (see page 76). Both warning lights are flashing red There is an internal problem. Turn off the projector and unplug it from the electrical outlet. Then contact Epson for assistance (see page 76). Solving Picture Problems You cannot turn on the projector. ¦ Make sure the power cord is connected and the power switch on the back of the projector is turned on. Then wait a moment for the Ppower button to light up before pressing the Ppower button on the projector or the On button on the remote control. ¦ If you’ve set the Control Panel Lock, the control panel buttons are disabled; you must use the remote control to turn on the projector (see page 32). ¦ If you’ve set the Child Lock, you have to press the Ppower button on the projector for 3 seconds to turn on the projector, or use the remote control (see page 32). No picture appears on the screen or you see the No Signal message displayed. ¦ Press one of the Source buttons on the remote control, or press the source button on the projector, to select the correct input source. Allow a few seconds for the projector to sync up after pressing the button. ¦ Press the Blank button on the remote control to make sure the picture hasn’t been turned off temporarily. ¦ Check that the power light is on and not flashing, and the lens cover is open. ¦ The projector may be in standby (or sleep) mode. If the Ppower button is lit and the power light is off, press the Ppower button to turn the projector back on. ¦ Make sure your video equipment is turned on. ¦ Make sure your cable(s) are connected correctly (see page 17). 70 Problem Solving 3D content does not display or does not display correctly. ¦ Press the 2D/3D button on the remote control to switch to 3D viewing mode, if necessary. ¦ Make sure you are within the 3D viewing range (see page 11). ¦ Check that your video device and media are both 3D-compatible. Refer to the documentation that came with your video device for more information. ¦ If you are viewing 3D content from a video device or game console, press the Menu button on the remote control, select the Signal menu, then select 3D Setup, then select 3D Format. Make sure that the Auto option is selected. ¦ If you are viewing a 3D television broadcast, you may have to manually select the 3D Format setting (see page 41). ¦ Make sure the Inverse 3D Glasses option is set to No (see page 41). ¦ If your video device is connected to the WirelessHD Transmitter (PowerLite Home Cinema 5010e only), see page 75. Only part of the picture is displayed, or the picture is distorted. ¦ Press the Aspect button on the remote control to select a different aspect ratio (see page 26). ¦ If the Aspect is set to Zoom, you may need to use the Zoom Caption Pos. option to see the top or bottom section of the screen so that subtitles are visible (see page 50). ¦ Check the Overscan setting to make sure it’s adjusted correctly (see page 49). ¦ Use the Position setting to repo...
Otros modelos de este manual:Cine en casa - POWERLITE 5010E (2.27 mb)