Votos - 1, Puntuación media: 4
(
)
)
|
Otros manuales para este modelo:
Cine en casa - DAV-SR4W (3.81 mb)
Cine en casa - DAV-SR4W (3.92 mb)
Resumen del manual
removal of insulation. After connecting all the components, speakers, and AC power cord (mains lead), output a test tone to check that all the speakers are connected correctly. For details on outputting a test tone, see page 85. If no sound is heard from a speaker while outputting a test tone, or a test tone is output from a speaker other than the one currently displayed in the front panel display, the speaker may be short-circuited. If this happens, check the speaker connection again. Notes • Be sure to match the speaker cord to the appropriate terminal on the components: 3 to 3, and # to #. If the cords are reversed, the sound will lack bass and may be distorted. • If you connect the speaker cord incorrectly or turn up the volume in a state of a short circuit, “PROTECT” appears in the front panel display and the system enters standby mode. In this case, disconnect and then reconnect the AC power cord (mains lead) from the wall outlet (mains), and then turn the system on. 16GB To change the speaker cables If you want to use a different speaker cable, you can detach the plug for attachment to another cable. Detaching Catcher Getting Started With the catcher facing down, press and hold the plug down against a flat surface and remove the cords from plug. Attaching While pressing the plug down against a flat surface, insert the new speaker cords. Note that the cord marked with a line should be attached to the minus (-) side of the plug. Notes • Be careful not to damage the surface you use (desk, etc.) when attaching/detaching the speaker cords. • When using the subwoofer cord, note that the two outside black cords or the cords marked with letters are negative. (–) (+) (–) (–) (+) (–) • If you connect the subwoofer cord incorrectly or turn up the volume in a state of a short circuit, “PROTECT” appears in the front panel display and the system enters standby mode. In this case, disconnect and then reconnect the AC power cord (mains lead) from the wall outlet (mains), and then turn the system on. Tips • You can use any commercially sold speaker cable of gauge cord AWG #18 - AWG #22. • Before attaching a new cable, strip off 10 mm (13/32 in.) of its insulation and twist the bare wires of both cords. 10 mm 17GB About the wireless system This wireless system adopts the Digital Infrared Audio Transmission system (page 94). The following diagram indicates the infrared transmission area (the range that the infrared rays can reach). When using the IR receiver of the surround speaker (L) Top view Side view Infrared signal Infrared signal 10 10 10 10 IR transmitter IR transmitter Surround speaker (L) Approx. 10m Approx. 10m Surround speaker (L) IR receiver When using the IR receiver Top view Side view Infrared signal Infrared signal 10 10 10 10 IR transmitter IR transmitter IR receiver IR receiver Approx. 10m Approx. 10m Notes • Do not install the surround speaker (L) (or IR receiver) in a place exposed to direct sunlight or strong light such as an incandescent lamp. • Do not use the surround speaker (L) (or IR receiver) that is not supplied with the system. 18GB Step 2: Antenna (aerial) Hookups Connect the supplied AM/FM antennas (aerials) for listening to the radio. Terminals for connecting the antennas (aerials) Connect the To the AM loop antenna (aerial) AM terminals Getting Started FM wire antenna (aerial) FM 75. COAXIAL jack AUDIO IN VIDEO SURROUND BACK SAT SAT SPEAKER DIR-T1 AUDIO IN OPTICAL DIGITAL INR L R L CENTER FRONT LFRONT R WOOFERWOOFER EURO AV OUTPUT(TO TV) COAXIAL AM FM 75 AM loop antenna (aerial) FM wire antenna (aerial) Notes • To prevent noise pickup, keep the AM loop antenna (aerial) away from the system and other components. • Be sure to fully extend the FM wire antenna (aerial). • After connecting the FM wire antenna (aerial), keep it as horizontal as possible. Tip When you connect the supplied AM loop antenna (aerial), the cord (A) and the cord (B) can be connected in either terminal. A B continued 19GB Tip If you have poor FM reception, use a 75-ohms coaxial cable (not supplied) to connect the system to an outdoor FM antenna (aerial) as shown below. Outdoor FM antenna (aerial) System COAXIAL AM FM 75 20GB Getting Started Required cords SCART (EURO AV) cord for connecting a TV (not supplied) Step 3: TV and Video Component Hookups Required cords SCART (EURO AV) cord for connecting a TV (not supplied) Step 3: TV and Video Component Hookups Audio cords (not supplied) When connecting a cord, be sure to match the color-coded sleeves to the appropriate jacks on the components. White (L/audio) Red (R/audio) Terminals for connecting video components Connect the To the TV (VIDEO IN) T EURO AV OUTPUT (TO TV) jack VCR (AUDIO OUT) VIDEO (AUDIO IN) jacks Digital satellite receiver SAT (AUDIO IN) jacks (AUDIO OUT) Connecting the system to a TV Connect the system to your TV using the SCART (EURO AV) cord. Be sure to connect the SCART (EURO AV) cord to the T EURO AV OUTPUT (TO TV) jack on the system. When you conne...