Votos - 6, Puntuación media: 3.8
(
)
)
|
Fotos y especificaciones Sony HT-SF1000 |
Otros manuales para este modelo:
Cine en casa - HT-SF1000 (59.71 kb)
Cine en casa - HT-SF1000 (5.16 mb)
Resumen del manual
Do not use any type of abrasive pad, scouring powder, or solvent, such as alcohol or benzine. If you have any questions or problems concerning your receiver, please consult your nearest Sony dealer. 53GB Additional Information Troubleshooting If you experience any of the following difficulties while using the receiver, use this troubleshooting guide to help you remedy the problem. There is no sound, no matter which component is selected, or only a very low-level sound is heard. • Check that the speakers and components are connected securely. • Check that both the receiver and all components are turned on. • Check that MASTER VOLUME is not set to “VOL MIN”. • Press MUTING to cancel the muting function. • Check that you have selected the correct component with the input buttons on the remote or INPUT SELECTOR on the receiver. • The protective device on the receiver has been activated. Turn off the receiver, eliminate the short-circuit problem, and turn on the power again. There is no sound from a specific component. • Check that the component is connected correctly to the audio input jacks for that component. • Check that the cord(s) used for the connection is (are) fully inserted into the jacks on both the receiver and the component. • Check that you have selected the correct component with the input buttons on the remote or INPUT SELECTOR on the receiver. There is no sound from one of the front speakers. • Make sure you have connected to both the L and R jacks of an analog component, and not only to either the L or R jack. Use an audio cord (not supplied). The source sound input to the HDMI jack on the receiver is not output from the TV speaker.a) • Check the HDMI connection. • You cannot listen to the Super Audio CD by connecting HDMI. • Depending on the playback component, you may need to set up the component. Refer to the operating instructions supplied with each component. The left and right sounds are unbalanced or reversed. • Check that the speakers and components are connected correctly and securely. • Adjust the balance parameters using the LEVEL menu (page 34). There is severe hum or noise. • Check that the speakers and components are connected securely. • Check that the connecting cords are away from a transformer or motor, and at least 3 m away from a TV set or fluorescent light. • Move your audio components away from the TV. • The plugs and jacks are dirty. Wipe them with a cloth slightly moistened with alcohol. There is no sound, or only a very low-level sound is heard from the center/ surround speakers. • Select a CINEMA STUDIO EX mode (page 42). • Adjust the speaker level (page 26). There is no sound from the sub woofer. • Check that the sub woofer is connected correctly and securely. The surround effect cannot be obtained. • Make sure you have selected a sound field with MOVIE or MUSIC button. • Sound fields do not function for signals with a sampling frequency of more than 48 kHz. 54 fifl Dolby Digital or DTS multi channel sound is not reproduced. • Check that the DVD, etc. you are playing is recorded in Dolby Digital or DTS format. • When connecting the DVD player, etc., to the digital input jacks of this receiver, check the audio setting (the settings for the audio output) of the connected component. The FM reception is poor. • Use a 75-ohm coaxial cable (not supplied) to connect the receiver to an outdoor FM antenna as shown below. If you connect the receiver to an outdoor antenna, ground it against lightning. To prevent a gas explosion, do not connect the ground wire to a gas pipe. Outdoor FM antenna Ground wire (not supplied) ♦ To ground RDS does not work.b) • Make sure that you are tuned to an FM RDS station. • Select a stronger FM station. The RDS information that you want does not appear.b) • Contact the radio station and find out whether they actually provide the service in question. If so, the service may be temporarily out of order. There is no picture or an unclear picture appears on the TV screen or monitor. • Make sure you have connected the video output of your video component to the TV. • Move your audio components away from the TV. The source image input to the HDMI jack on the receiver is not output from the TV.a) • Check the HDMI connection. • Depending on the playback component, you may need to set up the component. Refer to the operating instructions supplied with each component. Radio stations cannot be tuned in. • Check that the antennas are connected securely. Adjust the antennas and connect an external antenna, if necessary. • The signal strength of the stations is too weak (when tuning in with automatic tuning). Use direct tuning (page 45). • Make sure you set the tuning interval correctly (when tuning in AM stations with direct tuning). • No stations have been preset or the preset stations have been cleared (when tuning by scanning preset stations). Preset the stations (page 47). continued 55GB Add...
Otros modelos de este manual:Cine en casa - HT-SS1000 (1.71 mb)