Votos - 5, Puntuación media: 4
(
)
)
|
Resumen del manual
For the center speaker 6 to 9 mm (1/4 to 3/8 inch) 265 mm (10 7/16 inches) For the other speakers 6 to 9 mm (1/4 to 3/8 inch) 170 mm (6 23/32 inches) 3 Hang the speakers on the screws. 4.6 mm (3/16 inch) 10 mm (13/32 inch) Rear of speaker Note • Use screws that are suitable for the wall material and strength. As a plaster board wall is especially fragile, attach the screws securely to a beam and fasten them to the wall. Install the speakers on a vertical and flat wall where reinforcement is applied. • Contact a screw shop or installer regarding the wall material or screws to be used. • Sony is not responsible for accident or damage caused by improper installation, insufficient wall strength or improper screw installation, natural calamity, etc. 26GB Installing the IR transmitter on a wall You can hang the IR transmitter on a wall when: – there is an obstruction between the IR transmitter and IR receiver of the surround speaker (L). – people often pass between the IR transmitter and IR receiver of the surround speaker (L). When hanging both the IR transmitter and surround speaker (L), adjust the position of the IR transmitter after deciding the position of the surround speaker (L). 1 Rotate the stand of the IR transmitter. IR transmitter Stand 2 Install two commercially available screws in the wall so that it protrudes 4 mm (3/16 inch). Install the screws 30 mm (1 3/16 inches) apart. 30 mm (1 3/16 inches) 4 mm (3/16 inch) 3 Hang the IR transmitter via the holes on the bottom of the stand on the screws. Make sure that the IR transmitter does not move after installation. IR transmitter Getting Started – ADVANCED Stand Tip • You can store the cords in the troughs in the bottom of the stand. Stand Troughs Note • Use screws suitable for the material and strength of the wall. • Do not install the IR transmitter to a wall of low strength. • Sony is not liable for any damage or accident incurred by incorrect installation (i.e. wall of low strength, etc.), incorrect use of this product, or natural disaster. • When connecting/disconnecting the cord, detach the IR transmitter from the wall first. 27GB Connecting the TV (Advanced) Sends the played back DVD image to the connected TV. Check the jacks of your TV, and choose connection method A, B, or C. Picture quality improves in order from A (standard) to C (HDMI). C TV with HDMI* IN jack IN To HDMI* OUT Y PB/CB PR/CR COAXIAL AM FM75 (DVD ONLY) OUT DMPORT FRONT R CENTER WOOFER FRONT L SUR R SUR L SPEAKER SPEAKER SAT / CABLE EURO AV OUTPUT(TO TV)SAT/CABLE DIR-T1 OPTICALCOAXIAL DIGITAL IN COMPONENT VIDEO OUT R LAUDIO IN (DVD ONLY) Y B B R R ABTo EURO AV T OUTPUT (TO TV) To COMPONENT VIDEO OUT TV with COMPONENT TV with EURO AV INPUT jack VIDEO IN jacks :Signal flow * HDMI (high-definition multimedia interface) The system incorporates High-Definition Multimedia Interface (HDMITM) technology. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. 28GB Note Note • When you connect the system and TV with the HDMI cord and the SCART (EURO AV) cord simultaneously, the TV may be set to SCART (EURO AV) input automatically. In this case, set to the desired input source on the TV, or use a SCART (EURO AV) cord that has separate audio connectors. A To connect to a TV with the SCART (EURO AV) cord (not supplied) . Be sure to connect the SCART (EURO AV) cord to the EURO AV T OUTPUT (TO TV) jack on the unit. When you connect using the SCART (EURO AV) cord, check that the TV conforms to S video or RGB signals. If the TV conforms to S video, change the input mode of the TV to RGB signals. Refer to the operating instructions supplied with the TV to be connected. B To connect to a TV with the COMPONENT VIDEO IN jacks Connect a component video cord (not supplied). To use the COMPONENT VIDEO OUT jacks (Y, PB/ CB, PR/CR), your TV monitor must be equipped with via COMPONENT VIDEO IN jacks (Y,PB/CB, PR/CR). If your TV accepts progressive format signals, you must use this connection and set the output channel of the system to progressive format (page 30). Getting Started – ADVANCED Green Blue Red C To connect to a TV with the HDMI (high-definition multimedia interface)/DVI (digital visual interface) IN jack Use a certified HDMI (high-definition multimedia interface) cord (not supplied) to enjoy high quality digital picture and sound through the HDMI OUT (high-definition multimedia interface out) jack. To connect to a TV with DVI (digital visual interface) input Use an HDMI (high-definition multimedia interface)-DVI (digital visual interface) converter cord (not supplied) with an HDMI (high-definition multimedia interface)-DVI (digital visual interface) adaptor (not supplied). The DVI (digital visual interface) jack will not accept any audio signals. Furthermore, you cannot connect the HDMI OUT (high-definition multimedia interface out) jack to DVI (digital visual interface) jacks that are not HDCP (high-bandwidth digital content ...