Votos - 2, Puntuación media: 3
(
)
)
|
Otros manuales para este modelo:
Cine en casa - HTR-110SS (2.25 mb)
Cine en casa - HTR-110SS (2.48 mb)
Cine en casa - HTR-110SS (2.17 mb)
Resumen del manual
There is no sound or only a very low-level sound no matter which component is selected. • Check that the speakers and components are connected securely and correctly. • Check that both the receiver and all components are turned on. • Check that you have selected the correct component on the receiver. • Check that MASTER VOLUME on the receiver is not set at “VOL MIN”. • Press MUTING to cancel the muting function. There is no sound from a specific component. • Check that the component is connected correctly to the audio input jacks for that component. • Check that the cord(s) used for the connection is (are) fully inserted into the jacks on both the receiver and the component. • Check that you have selected the correct component on the receiver. There is no sound from one of the front speakers. • Check that the component is connected correctly to the audio input jacks for that component. • Check that the cord(s) used for the connection is (are) fully inserted into the jacks on both the receiver and the component. The left and right sounds are unbalanced or reversed. • Check that the speakers and components are connected correctly and securely. • Adjust balance parameters in the LEVEL menu. There is severe hum or noise. • Check that the speakers and components are connected securely. • Check that the connecting cords are away from a transformer or motor, and at least 3 meters away from a TV set or fluorescent light. • Move your TV away from the audio components. • The plugs and jacks are dirty. Wipe them with a cloth slightly moistened with alcohol. There is no sound or only a very low-level sound is heard from the center or/and surround speakers. • Select a CINEMA STUDIO EX mode (page 24). • Adjust the speaker level (page 16). There is no sound from the subwoofer. • Check that the subwoofer is connected correctly and securely. The surround effect cannot be obtained. • Make sure the sound field function is on (press MOVIE or MUSIC). • Sound fields do not function for the signals with a sampling frequency of more than 48 kHz. Dolby Digital or DTS multi channel sound is not reproduced. • Check that the playing DVD, etc. is recorded in Dolby Digital or DTS format. • When connecting the DVD player/DVD recorder, etc. to the digital input jacks of this receiver, check the audio setting (settings for the audio output) of the connected component. The FM reception is poor. • Use a 75-ohm coaxial cable (not supplied) to connect the receiver to an outdoor FM antenna as shown below. If you connect the receiver to an outdoor antenna, ground it against lightning. To prevent a gas explosion, do not connect the ground wire to a gas pipe. Outdoor FM antenna ANTENNA AMU Receiver Ground wire (not supplied) To ground 36GB Radio stations cannot be tuned in. • Check that the antennas are connected securely. Adjust the antennas and connect an external antenna if necessary. • The signal strength of the stations is too weak (when tuning in with automatic tuning). Use direct tuning. • Make sure you set the tuning interval correctly (when tuning in AM stations with direct tuning). • No stations have been preset or the preset stations have been cleared (when tuning by scanning preset stations). Preset the stations (page 19). RDS does not work. • Make sure that you are tuned to an FM RDS station. • Select a stronger FM station. The RDS information that you want does not appear. • Contact the radio station and find out whether they actually provide the service in question. If so, the service may be temporarily out of order. Remote control The remote does not function. • The DISPLAY button on the remote is available for TUNER input only. • Point the remote at the remote sensor on the receiver. • Remove any obstacles in the path between the remote and the receiver. • Replace all the batteries in the remote with new ones, if they are weak. • Make sure you select the correct input on the remote. • To activate the buttons with orange printing, press TV and the button you want simultaneously. • Before you use the V/v/B/b button for receiver operation, press MAIN MENU. To operate other components, press TOP MENU/GUIDE or AV MENU after pressing the function button. Error message If there is a malfunction, the display shows a message. PROTECT Irregular current is output from the speakers. The receiver will automatically turn off after a few seconds. Check the speaker connection and turn on the power again. If this problem persists, consult your nearest Sony dealer. If you are unable to remedy the problem using the troubleshooting guide Clearing the receiver’s memory may remedy the problem (page 14). However, note that all memorized settings will be reset to their factory settings and you will have to readjust all settings on the receiver. If the problem persist Consult your nearest Sony dealer. Reference sections for clearing the receiver’s memory To clear See All memorized settings page 14 Customized sound fields page 27 Additional Information 37G...
Otros modelos de este manual:Cine en casa - HTD-710SF (1.22 mb)
Cine en casa - HTD-710SS (1.22 mb)
Cine en casa - HTP-32SS (1.22 mb)
Cine en casa - HTR-210SS (1.22 mb)