Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
In these case the files will be skipped automatically. • There may be cases where no information can be displayed. • Displaying title, artist and album name is only supported for MP3 files. En USB playback USB playback Chapter 7: USB playback Playing USB storage devices It is possible to listen to two-channel audio using the USB interface on the front of this receiver. • Pioneer does not guarantee that any file recorded on a USB storage device will play or that power will be supplied to a USB storage device. Also note that Pioneer will accept no responsibility whatsoever for loss of files on USB storage devices caused by connection to this unit. 1 Press USB as the input source. “USB/iPod” is shown on the main display. 2 Connect the USB storage device. The number of folders or files stored on the connected USB storage device appear on the main display automatically. • This receiver does not support a USB hub. • If an iPod/iPhone/iPad is connected to the unit, the unit will automatically begin charging it. PHONES AUDIO IN .. USB storage device (commercially available) 3 When the recognition is completed, press ./. to start playback. • When changing to a different input source, stop the USB memory playback first before changing. 4 Disconnect USB storage device from the USB terminal. Turn the power off before removing the USB storage device. Note • USB flash drive that supports USB 2.0 can be used. • This unit may not recognize a USB storage device, play files or supply power to a USB storage device. For details, see When a USB storage device is connected on page 30. • When a USB storage device is not playing and no operations have been performed for more than 30 minutes, the unit will automatically power off. Repeat play Repeat play can play one track, all tracks or a programmed sequence continuously. To repeat one track: Press REPEAT repeatedly until “REPEAT ONE” appears. Press ENTER. To repeat all tracks: Press REPEAT repeatedly until “REPEAT ALL” appears. Press ENTER. To repeat desired tracks: Perform steps 1 to 5 in “Programmed play (CD or MP3/WMA)” section on next page and then press REPEAT repeatedly until “REPEAT ALL” appears. Press ENTER. To cancel repeat play: Press REPEAT repeatedly until “REPEAT OFF” appears. Press ENTER. Note • After performing repeat play, be sure to press .. Otherwise, the file of USB storage device will play continuously. • During repeat play, random play is not possible. Random play The file of USB storage device can be played in random order automatically. To random play all tracks: Press RANDOM repeatedly until “RANDOM ON” appears. Press ENTER. To cancel random play: Press RANDOM repeatedly until “RANDOM OFF” appears. Press ENTER. Note • If you press the . during random play, you can move to the track selected next by the random operation. On the other hand, the . does not allow you to move to the previous track. The beginning of the track being played will be located. • In random play, the unit will select and play tracks automatically. (You cannot select the order of the tracks.) • During random play, repeat play is not possible. En USB playback USB playback Specify the folder to play To specify the folder to play, perform the following steps. 1 Press USB, and connect the USB storage device. 2 Press FOLDER, and press ./. to select desired playback folder. 3 Press ENTER. Playback will start from the first song of the selected folder. • Even if it is stopped, it is possible to press ./., to select a folder. Switch the display contents The unit can display the information recorded in the USB storage device. For details, see Switch the display contents on page 20. Playing in the desired order (Programmed Play) The unit can play folders stored on a USB storage device in the desired order. For details, see Programmed play (CD or MP3/WMA) on page 19. En Using the tuner Using the tuner Chapter 8: Using the tuner X-HM21DAB-K, X-HM11DAB-K: Equipped with FM tuner/ DAB; not equipped with AM tuner X-HM11-K: Equipped with FM/AM tuner; not equipped with DAB Listening to the radio broadcasts The following steps show you how to tune in to FM and AM radio broadcasts using the automatic (search) and manual (step) tuning functions. Once you are tuned to a station you can memorize the frequency for recall later. See Saving station presets below for more on how to do this. DISPLAY FOLDER MENU PRESET VOLUME ST/MONO ASPM PTY DISPLAY + MUTE TUNE– TUNE+ DIMMER ..... .. – + – MEMORY /PROGRAM 0 RDS ENTER STANDBY/ON .. CD USB TUNER AUDIO IN DISPLAY FOLDERTUNE+ 1 2 3 4 5 6 7 8 9 0 BT AUDIO CLOCK/TIMER SLEEP EQUALIZER P.BA S S BASS/TREBLE RANDOMCLEAR REPEAT OPEN/CLOSE Tuning 1 Press the . STANDBY/ON to turn the power on. 2 Press TUNER repeatedly to select desired frequency band (FM or AM). 3 Press TUNE +/– on the remote control to tune in to the desired station. Automatic tuning: Press and hold TUNE +/–, scanning will start automatically and the tuner will stop at the first receivable broadcast station. ...
Otros modelos de este manual:Cine en casa - X-HM11DAB-K (3.93 mb)
Cine en casa - X-HM21DAB-K (3.93 mb)