Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Do not use fly cutters or multiple-part cutters, as they can come apart or become unbalanced in use. 24. Make sure the spindle has come to a complete stop before touching the workpiece. 25. To avoid injury from accidental starting, always turn the switch off and unplug the drill press before installing or removing any accessory attachment or making any adjustment. CAUTION! Do not expose to rain or use in damp locations. WARNING! For your own safety read instruction manual before operating drill press. Wear eye protection, do not wear gloves, necktie or loose clothing, clamp workpiece or brace against column to prevent rotation, use recommended speed for drill accessory and workpiece material. 1 Know your product Before using the drill press, familiarise yourself with all the operating features and safety requirements. Use the tool only for the applications intended. All other applications are expressly ruled out. 21 13 2 3 12 1. Pulley cover 2. Belt tension lock knob 3. Head lock set screw 4. Feed handle x 3 5. Column 6. Column support 7. Column support bolts x 3 8. Base 9. Support lock 10. Table assembly 11. Chuck 12. Depth scale 13. Head assembly 14. ON/OFF Switch 15. Collar stop 16. Collar screw 17. Collar nut 18. Hex key 19. Feed wheel hub 20. Depth scale nut 21. Pulley cover knob 22. Quill 23. Chuck key 22 19 20 4 15 5 11 10 6 7 8 14 9 17 15 18 16 23 Accessories The tool is supplied with the following accessories: - 4mm Hex key - Chuck Key Unpacking Carefully remove all parts from the packaging and check that they are in good condition. Check that the following parts are supplied. Bags of fittings comprising: - 4mm hex key - Belt tension lock knob - Support lock - 3 x 8mm x 20mm bolts - 3 x feed handles - Keyed chuck - Chuck key - Collar stop - Collar screw - Collar nut We recommend that you purchase your accessories in the store from where you purchased the tool. Use good quality accessories and the brand recommended by the vendor. Assembly The following tools are required to assemble the drill press • 4mm hex key (supplied) • Wrench (not supplied) • Phillips head screwdriver (not supplied) Assembly time The DP2 drill press will take approximately 15 minutes to assemble. IMPORTANT. If any parts are missing , please contact the place of purchase. DO NOT attempt to operate the machine until the missing parts are available. WARNING. Ensure the machine is disconnected from the mains plug at all times during assembly and maintenance. Place the base (8) on a flat surface. Place the column support (6) on base and align the 3 holes in the column support with the holes in the base (8). Using the 3 x 8mm diameter x 20mm long column support bolts secure the column support to the base and tighten with a wrench (not supplied). Slide the table assembly (10) onto the column (5). Install the support lock (9) handle, from the right side into the rear of the table support (10) and tighten by hand. Once tightened, ensure the table is fixed and cannot move. Lift the head assembly (13) and slide it onto the column assembly (5) as far as possible. Align the head assembly with the table assembly (10) and base (8). Using the hex key (18) tighten the head lock set screw (3) into the head assembly. This will secure the head onto the column. Screw the feed handles (4) into the threaded holes of the feed wheel hub (19) and tighten. Clean the spindle nose of the chuck (11) with a clean cloth. Push the chuck up into the spindle nose as far as possible. Lightly tap the nose of the chuck with a piece of wood to ensure proper fitting of the chuck on the spindle lock. Fit the collar stop (15) over the quill (22). Place the collar nut (17) into the designated position of the collar stop and in the other of side of the collar stop feed the collar screw (16) in and tighten into the collar nut. Insert the depth scale (12) into the depth collar stop (15) and fit into the depth collar and place the depth scale nut (20) onto the end of the depth scale. Open the pulley cover to discover the motor speed pulleys and belt. Refer to the inside of the pulley cover for speed reference. 2500 RPM1900 RPM1400 RPM890 RPM500 RPM Note. When fitting belts it is easier to place the belt onto the small pulley and then turn it onto the larger pulley. Unscrew the screw from the pulley cover knob (21) and place it through the hole on the right side of the pulley cover (1) and tighten. To apply tension to the belt, loosen the belt tension lock knob (2) and push the motor housing backwards. Tighten belt tension lock knob. Replace and secure the pulley cover. Adjusting the table height CAUTION. Always ensure that the drill press is switched off and the plug is removed from the power point before making any adjustments. Loosen the support lock (9). Rotate the handle in an anti-clockwise direction to loosen the table support (10). Raise/Lower the table support to the desired height. Tighten the support lock to secure the table. Adjusting the table angle CAUTION. Al...