Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
All persons who use and service the machine have to be acquainted with this Manual and must be informed about its potential hazards. Children and infirm people must not use this tool. Children should be supervised at all times if they are in the area in which the tool is being used. It is also imperative that you observe the accident prevention regulations in force in your area. The same applies for general rules of occupational health and safety. The manufacturer shall not be liable for any changes made to the tool nor for any damage resulting from such changes. Even when the tool is used as prescribed it is not possible to eliminate all residual risk factors. The following hazards may arise in connection with the tool’s construction and design: • Damage to the lungs if an effective dust mask is not worn. • Damage to hearing if effective earmuffs are not worn. • Damage to eyes if effective goggles are not worn • Risk of injury unless hands are kept well clear of cutting devises Unpacking Due to modern mass production techniques, it is unlikely that your GMC Power Tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury. Know your product This mini-drill is ideal for drilling, sanding, milling, grinding, polishing, sharpening, engraving, cutting and paring. It can be used on most metals, glass, wood and ceramics. Use the machine and accessories only for intended applications. All other applications are expressly ruled out. The MX372 Mini Drill is supplied as part of a kit that includes accessories and a storage case. 1. Cord protector 2. Wire loop 3. On/off switch 4. Variable speed dial 5. Spindle lock button 6. Collet nut 7. Collet 8. Brush caps 9. Collet cover 8 4 2 5 6 7 9 1 8 3 3 4 5 Operation WARNING. Before connecting a tool to a power source (power point receptacle, outlet, etc.) be sure that the voltage supply is the same as that specified on the nameplate of the tool. A power source with a voltage greater than that specified for the tool can result in serious injury to the user, as well as damage to the tool. If in doubt, do not plug in the tool. Using a power source with a voltage less than the nameplate rating is harmful to the motor. Switch on 1. Set the variable speed dial to 1 and push the on/off switch (3) to “I”, the machine is in continuous operation, and will start at minimum speed. Switch off 1. Reset the variable speed dial (4) to 1 and push the on/off switch to position “0”. Varying the speed 1. You can use the variable speed dial to alter the speed of the collet, as follows: • Position 1-Slow • Position 3-Medium • Position 6-Fast 2. Select the correct speed for the work and type of bit you are using. In general, lower speeds are best suited for large tools and higher speed for smaller tools. Holding the tool • Small milling cutters/grinders pencils - high speed • Large milling cutters/grinders pencils - low speed 1. For jobs such as milling or engraving where precision is required, hold the mini-drill like a pen. 2. For heavier work like cutting or grinding hold the machine in the palm of your hand. Changing accessories 1. Make sure that the machine is switched off and the plug removed from the power before you commence changeover. 2. Loosen and tighten collet fully using the 2 in 1 Wrench provided. (always ensure bits are tight before commencing any work with your tool). 3. Press and hold down the spindle lock button (5) and unscrew the Collet nut (6). 4. Select a suitable Collet for the accessory to be used and insert it in the collet nut shaft. 5. Turn the Collet nut in an anti-clockwise direction to loosen and, when the bit is in place, turn the Collet nut in clockwise direction to lock it in place, whilst depressing the spindle lock. 6. Make sure that the bit is inserted as far as possible. Having too much shaft exposed could cause it to damage or bend. Locating a cutting/sanding disc 1. Locate the disc holder in the Collet nut. 2. Remove the screw from the end with the 2 in one wrench provided, and insert the screw through the cutting disc. 3. Replace the screw and tighten, attaching the cutting disc onto the holder. (Do not over-tighten) Locating a sanding drum 1. Loosen the small screw in the top of the holder. 2. This allows the rubber to slacken. 3. Slide the sanding drum onto the holder. 4. Secure the sanding drum in place by tightening the screw causing the rubber drum to bulge and grip the drum. (Do not over-tighten) Maintenance 1. Store the machine, instruction manual and, where necessary, the accessories in the original packaging. In this way you will always have all the information and parts ready to hand. Cleaning 1. Keep the tool’s air vents unclogged and clean at all times. 2. Remove dust and dirt regularly. Cleaning is best done with a rag. 3. Never use caustic agents to clean plastic parts. CAUTION. Do not...