Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
2. To swing the table, loosen the column lock handle and swing the table to the desired position. Re-tighten the column lock handle. For long workpieces, swing the work table away 180° and use the base as your table. Figure 13. 3. To rotate the table, loosen the table lock handle, rotate the table to the desired position and re-tighten the table lock handle. Figure 14. -12- G1199/G1200 Drill Press Figure 14. Chuck Removal 1. Adjust the stationary depth to three inches (see depth setting instructions). 2. Rotate the spindle manually and line up the internal spindle slot with the slot on the side of the quill. The end of the drill chuck (the tang) should be visible through the slot at this point. 3. Insert the wedge shifter through the slot in the spindle with the tapered edge facing down. Figure 16. 4. When the tapered edge of the wedge shifter 4. To tilt the table, loosen the pivot bolt and contacts the top of the taper, tap the wedge remove the locator pin (Figure 15). This is shifter lightly with a hammer until the taper done by tightening the nut until the pin is and chuck are loose. Do not allow the taper extracted from its hole. Tilt the table to the and chuck to fall onto the table. desired angle (up to 45°) and re-tighten the pivot bolt. Re-insert the locator pin when returning the table to zero degrees. Figure 15. Figure 16. Removing the chuck. G1199/G1200 Drill Press -13 SECTION 4: OPERATIONS Safety Rules Now that your drill press is assembled and in place, you are ready to begin using it. Your new drill press is a simple piece of equipment to set up and operate. It is a versatile tool that can be used to perform many different operations such as: Drilling, Boring, Sanding, Mortising and Shaping. For your own protection, please read and follow these safety precautions. •While operating this machine, do not wear jewelry, loose clothing, necklaces or neckties. Long sleeves on shirts should be rolled up or securely buttoned at the cuff. • Persons with beards and/or long hair should consider the use of a hat, hair net or similar protective equipment. • Always use face/eye protection when operating the drill press. A full face shield will afford the best protection followed by safety glasses with side shields. • All adjustments or maintenance should be done with the power off and the drill press unplugged. • Never use tools that are in poor condition. Cutting tools that are dull or damaged are difficult to control and may cause serious injury. • Thoroughly clean the machine and surrounding area after use. • Feed the drill bit evenly into the workpiece. Back the bit out of deep cuts to cool and clean the bit. • If you have questions about your drill press, ask a professional or an experienced user. • Never attempt to clean wood or metal cuttings from drill bits while the drill press is running. • The workpiece must be held securely in place using a drill press vise or clamp. • Never use a bit with a tapered shank or square bit in a drill chuck. • Use the correct speed for the size of bit and material being drilled. • Always remove the key from the chuck before starting drill press. • Remove metal cuttings with a brush, never by hand. • Perform machine inspection and maintenance service routinely. • Never drill sheet metal unless it is securely clamped to the table. • Work should be secured in such a way so as to avoid drilling into the table. • When changing speeds, always disconnect the machine from the power source. This sums up our review of safety guidelines. Remember that every shop has its own specific hazards. Be sure, above all else, to use good common sense and reasonable caution each time you start this drill press, or any woodworking machinery. Proper safety standards rarely take any more time or energy when followed religiously. Develop a habit of safety. Caution Always wear ANSI-approved safety glasses or goggles when operating equipment — particularly when testing new tools or machinery. Do not allow visitors into your workshop when testing or operating equipment. -14- G1199/G1200 Drill Press Test Run Drill Changes Once the assembly is complete and the adjustments are done to your satisfaction, you are ready to test the machine. Turn on the power supply at the main panel. Press the START button. Make sure that your finger is poised on the STOP button, just in case there’s a problem. The drill press should run smoothly, with little or no vibration or rubbing noises. Strange or unnatural noises should be investigated and corrected before operating the machine further. WARNING: DO NOT attempt to investigate or adjust the machine while it is running. Wait until the machine is turned off, unplugged and all working parts have come to a rest before you do anything! If noises occur that can not be found by visual inspection, feel free to contact our service department for help. To insert or change a bit, care must be taken to secure the bit firmly in place. When changing bits, proceed as follows: 1...
Otros modelos de este manual:Taladros y shuropopverty - G1200 (647.28 kb)