Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
To use the Battery Adapter Cable, simply insert the 12 Volt Plug-In into the Adapter. When it is safe to do so, connect the RED clamp to the POSITIVE terminal of a 12 volt battery. Connect the BLACK clamp to a clean grounded part of the vehicle such as the engine block or frame member. NEVER leave either clamp attached to the vehicle while the impact wrench is not being used; disconnect clamps immediately as soon as work is finished. Also, make certain that neither clamp can come into contact with any other wire or metal portion of the vehicle’s engine. See FIGURE 1. NOTE: If the engine is left running while performing this operation, be sure to avoid placing any cables or clamps, or your hands, clothes, hair or any other appendage in close proximity to the moving parts of the engine. FIGURE 1 12 Volt Plug-In (24) Adapter (40) Clamp Trigger (26) Anvil (4) 12 Volt Plug-In (24) FIGURE 2 SKU 92349 For technical questions, please call 1-800-444-3353 Page 4 Operation (continued) WARNING: Working around vehicle engines whether running or not is inherently dangerous, and extraordinary precautions outside the scope of this booklet are required. Refer to the owner’s manual of your vehicle for more information. 4. NOTE: Unlike air-operated or 120V AC impact wrenches, this wrench will build up inertia before striking a blow.This is normal, and DOES NOT INDICATE A PROBLEM. 5. Make sure the vehicle is parked safely away from all other moving traffic. Be sure the vehicle is parked on a flat, dry, level surface. Be sure the vehicle’s emergency brake is set, and the tires have wheel blocks preventing movement. 6. Select the appropriate size socket to fit the wheel lug nut. Attach the socket to the Impact Wrench by pressing them on to the Anvil (4). Only use impact sockets and attachments. 7. Position an appropriate lift (not included) under the lift point for each wheel to be removed. (Follow the vehicle and lift manufacturer’s instructions for doing so.) Lift the vehicle until the wheel is off the ground, and support the vehicle securely on jack stands (not included). 8. The Impact Wrench is reversible. To operate the Impact Wrench in a forward (tightening) direction, set the Directional Lever toward the “R” symbol - see FIGURE 3. To operate the Impact Wrench in reverse direction, set the Directional Lever toward the “L” symbol. If the Directional Lever is set in the middle, the unit will not turn in either direction. Using the Impact Wrench in reverse, remove the wheel lug nuts according to the manufacturer’s recommendations. (In most cases, the manufacturer will recommend that you remove the lugs in an alternate pattern, moving around the wheel.) FIGURE 3 Note: For night use, this Impact Wrench has a LED (27) light. See FIGURE 4. Trigger (26) Directional Lever FIGURE 4 LED (27) SKU 92349 For technical questions, please call 1-800-444-3353 Page 5 Operation (continued) 9. Occasionally, you will have to manually break a nut loose before you can remove it with the Impact Wrench. To do so, use a Breaker Bar (not included) and Socket to break the nut loose. Then, proceed as discussed in number 8 on page 5. 10. Replace the wheel on the vehicle hub, aligning the wheel studs with the bolt holes in the wheel. 11. Install the wheel lug nuts, following the vehicle manufacturer’s recommendations. To avoid cross-threading the lug nuts, thread the nuts on by hand first, before using the Impact Wrench. CAUTION Do not use the Impact Wrench to tighten the lug nuts. The torque may exceed the vehicle specifications and damage may result. 12. When the wheel is securely refastened, use a torque wrench (not included) to check the torque on all bolts and ensure that the tightness meets the manufacturer’s recommendations. Check under the vehicle and remove any tools. Lower the vehicle, disconnect the tool and replace the lift and the Impact Wrench to their storage places. Maintenance 1. When not in use, store your Impact Wrench and its accessories in its case, in a secure, dry place. Protect it from water, moisture, oil, fuel, grease or other foreign materials which may damage the case, moving parts, or electrical components. 2. This tool should only be repaired by a qualified technician. 3. The 12 Volt Plug-In (24) assembly has a fuse that will eventually need replacing. Remove the Cap at the end of the Plug-In and replace the fuse making sure to replace the pieces below, in the exact same order as shown. Only replace the fuse with another 12A-250V fuse of the same style. 12 Volt Plug-In (24) Cap Fuse SKU 92349 For technical questions, please call 1-800-444-3353 Page 6 Parts List Part No. Description Part No. Description 1 Bearing 21 Bolt 2 Anvil Bearing 22 Cable Block 3 Radial Bearing 23 Cable Bushing 4 Anvil 24 12V Plug-In 5 Oil Bearing 25 Left Housing 6 Rachet Wheel Base 26 Trigger 7 Wheel 27 LED 8 Wheel Tray 28 Bolt 9 Pull Spring 29 Wheel 10 Wheel Brace 30 Pull Spring 11 Rachet Wheel Bearing 31 Bolt 12 Pedestal Bearing 32 Bolt 13 Gear 33 P...