Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
For a clockwise rotation, move the Forward/Reverse Button to the right. For a counterclockwise rotation, move the Forward/Reverse Button to the left. To avoid damage to the Impact Wrench, always wait until the tool completely stops before changing rotational directions. (See Figure D.) 4. 1/2” Drive Impact Head (7): The 1/2” Impact Head features a spring and ball to securely hold a socket. The Impact Head accepts all sizes of standard and metric sockets having a 1/2” drive. (See Figure D.) REV 03/05 SKU 92798 For technical questions, please call 1-800-444-3353. Page 9 5. Battery (37): The power source for the Impact Wrench is a rechargeable, 19.2 VDC Battery. Make sure to follow all safety precautions when working with the Battery. (See Figure D.) 6. Charger (39): The Charger is powered by plugging its Power Plug into a 120 volt, grounded, electrical outlet. NEVER attempt to power the Charger with any other electrical source other than a 120 volt, grounded electrical outlet. (See Figure D.) FIGURE D TO 120 VOLT, GROUNDED, ELECTRICAL OUTLET. BATTERY (37) CHARGER (39) IMPACT HEAD (7) TRIGGER (36) FORWARD/REVERSE SWITCH (32) BATTERY (37) TO CHARGE THE IMPACT WRENCH 1. NOTE: The Battery (37) requires charging. The first charge requires 1 hour charge time prior to using the Impact Wrench. (See Figure D.) 2. The Battery (37) should only be recharged when the Impact Wrench begins to run slowly. (See Figure D.) 3. When the Battery (37) requires recharging, a 1 hour charge allows the tool to operate at full power. Do not recharge the Battery longer than 1 hour, as damage to the Battery and/or Impact Wrench will occur. (See Figure D.) 4. Make sure the Trigger (36) on the Impact Wrench is in its “OFF” position. Slide the Battery (37) off the handle of the Impact Wrench. Insert the Battery into the charging socket of the Charger (39). Then plug the Charger into the nearest 120 volt, grounded, electrical outlet. (See Figure D.) SKU 92798 For technical questions, please call 1-800-444-3353. Page 10 5. Verify that the RED Charging Indicator Light comes on. If it does not illuminate, check the power connection or try a different electrical outlet. Charge the Battery (37) for 1 hour. NOTE: When the Battery is fully charged the RED Charging Indicator Light will turn off, and the GREEN Charged Light will illuminate. Subsequent charging can also be done in 1 hour. (See Figure D.) 6. While charging, the Battery (37) and Charger (39) may become warm to the touch. This is normal, and does not indicate a problem. (See Figure D.) 7. Once the Battery (37) is fully charged, disconnect the Charger (39) from the electrical outlet. Remove the Battery from the Charger, and insert the Battery into the handle of the Impact Wrench. (See Figure D.) 8. NOTE: If charging more than one Battery (37), allow the Charger (39) to cool down before reusing. (See Figure D.) OPERATING INSTRUCTIONS 1. Before installing a socket, make sure the Battery (37) is removed from the Impact Wrench to avoid accidental starting. Then, firmly insert the Socket onto the 1/2” Impact Head (7) of the tool. (See Figure D.) 2. Whenever possible, secure the workpiece in place, using a vise or clamps (not included). 3. Insert the fully charged Battery (37) into the handle of the Impact Wrench. (See Figure D.) 4. Use the Forward/Reverse Switch (32) to select the turning rotation of the Impact Wrench. (See Figure D.) 5. Insert the socket onto the nut that is to be loosened/tightened. 6. Make sure to hold the Impact Wrench firmly with both hands, as torque from the Motor will cause the tool to twist. Then, squeeze the Trigger (36) to turn on the Impact Wrench. (See Figure D.) 7. When finished, release the Trigger (36) to stop the Impact Wrench. Then, remove the Battery (37) and socket from the tool. (See Figure D.) 8. Make sure to store the Impact Wrench in a dry, clean location out of reach of children and other unauthorized people. REV 03/05 SKU 92798 For technical questions, please call 1-800-444-3353. Page 11 INSPECTION, MAINTENANCE, AND CLEANING 1. WARNING! Always let the Trigger (36) rest in its “OFF” position, remove the Battery (37) from the tool, and unplug the Charger (39) from its electrical outlet before performing any inspection, maintenance, or cleaning. 2. Before each use: Inspect the general condition of the Impact Wrench. Check for misalignment or binding of moving parts, cracked or broken parts, leaking Battery, damaged Charger wiring, chipped or broken sockets, and any other condition that may affect its safe operation. If abnormal noise or vibration occurs, have the problem corrected before further use. Do not use damaged equipment. 3. Daily: With a clean cloth, remove all dirt, grease, and oil from the Impact Wrench. Do not immerse the Impact Wrench in any liquids. 4. It may become necessary at sometime to replace or clean the two Carbon Brushes (29) when the Motor performance decreases, or stops working completely. To replace the Carbon Brushes: Remove th...