Votos - 1, Puntuación media: 3
(
)
)
|
Resumen del manual
If the cartridge does not slide in easily, it is not being inserted correctly. Charging Plug the fast charger into your power source. Insert the battery cartridge so that the plus and minus terminals on the bat- tery cartridge are on the same sides as their respective markings on the fast charger. Insert the cartridge fully into the port so that it rests on the charger port floor. Press the start button (red). The charging light will come on and charging will begin. If the charging light does not come on, press the reset button (yellow] first, then the start button (red). If the charging light goes out within 10 seconds even ifter pressing the reset button and start button a couple of times, the battery cartridge is dead. (CAUTION: Wait for more than 5 seconds after the charging light goes out to press the reset button again.) Replace it with a new one. When the charging light goes out after about one hour, you may remove the fully charged battery cartridge. After charging, unplug the charger from the power source. CAUTION : 0 Your new battery cartridge is not charged. You will need to charge it before use. 0 Do not keep the button pressed in with tape, etc. or the circuit will not function pro- perly. Also, a malfunction of the charger may result possibly causing overheating, etc. If you try to charge a cartridge from a just-operated tool, sometimes the charging light will not come on. If this occurs, let the cartridge cool off for a while. Then re-insert it and try to charge it once more. 0 When you charge a new battery cartridge or a battery cartridge which has not been used for a long period, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharging it almost completely a couple of times. 0 If you wish to charge two battery cartridges, allow 15 minutes between chargings on the fast charger. Installingor removing drill bit or driver bit CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing the bit. To install the bit, push the sleeve up to- ward the "FREE" side and turn the sleeve counterclockwise while holding the ring Place the bit in the chuck as far as it will go. Hold the ring firmly and turn the sleeve clockwise to tighten the chuck. Then push Sleeve PT the sleeve down toward the "LOCK" side. See illustration. s- To remove the bit, push the sleeve up toward the "FREE" side and turn the sleeve counterclockwise while holding the ring with your other hand. CAUTION : 0 Do not attempt to turn the sleeve forcibly when the sleeve is in the "LOCK" position. The sleeve may be damaged. 0 Always push the sleeve down toward the "LOCK' side before operation. If you operate the tool with the sleeve in the "FREE" position, the chuck may loosen and the bit may come out unexpectedly. Switch action Tool speed is increased by increasing pres- sure on the trigger. To start the tool, simply pull the trigger. Release the trigger to stop. Trigger switch I; I 1 CAUTION : Before inserting the battery cartridge into the tool, always check to see that the trigger switch actuates properly and returns to the "OFF" position when released. Reversing switch action This tool has a reversing switch to change the direction of rotation. Move the revers- ing switch to the left for clockwise rotation or to the right for counterclockwise. CAUTION : *Always check the direction of rotation before operation. .Move the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool. Speed change To change the speed, slide the speed change lever to the "H" side for high speed or "L" side for low speed. To slide the speed change lever easily, pull the trigger slightly while pushing the speed change lever. Be sure that the speed change lever is set to the correct position before operation. Use the right speed for your job. Speed change lever i \\ CAUTION : Always set the speed change lever fully into the correct position. If you operate the tool with the speed change lever positioned halfway between the "H" side and "L" side, the tool may be damaged. Operation 1) Hammer drilling operation : When drilling in concrete, granite, tile, etc., turn the knob so that the amark on the knob points to the mark. Be sure to use a tungsten-carbide tipped bit. To position a hole accurately, start the tool slowly and then increase the speed gradually. Do not apply more pressure when the hole becomes clogged - After drilling the hole, use the blow-out bulb to clean the dust out of the hole. I 2) Drilling operation : When drilling in wood, metal or plastic materials, turn the knob so that the mark on the knob points to the mark. Knob 0 Drilling in wood When drilling in wood, best results are obtained with wood drills equipped with a guide screw, The guide screw makes drilling easier by pulling the bit into the workpiece. Dr...