Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
Replace it with a new one. For DC1413 002787 • Plug the battery charger into the proper AC voltage source. The charging light will flash in green color. • Insert the battery cartridge so that the plus and minus terminals on the battery cartridge are on the same sides as their respective markings on the battery charger. Insert the cartridge fully into the port so that it rests on the charger port floor. • When the battery cartridge is inserted, the charging light color will change from green to red and charging will begin. The charging light will remain lit steadily during charging. • When the charging light color changes from red to green, the charging cycle is complete. • If you leave the battery cartridge in the charger after the charging cycle is complete, the charger will switch into its “trickle charge (maintenance charge)” mode which will last approximately 24 hours. • After charging, unplug the charger from the power source. CAUTION: • The battery charger is for charging Makita battery cartridge. Never use it for other purposes or for other manufacturer’s batteries. • When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharging it completely and recharging a couple of times. • If you charge a battery cartridge from a just-operated tool or a battery cartridge which has been left in a location exposed to direct sunlight or heat for a long time, the charging light may flash in red color. If this occurs, wait for a while. Charging will begin after the battery cartridge cools. The battery cartridge will cool faster if you remove the battery cartridge from the battery charger. • If the charging light flashes alternately in green and red color, a problem exists and charging is not possible. The terminals on the charger or battery cartridge are clogged with dust or the battery cartridge is worn out or damaged. Trickle charge (Maintenance charge) If you leave the battery cartridge in the charger to prevent spontaneous discharging after full charge, the charger will switch into its “trickle charge (maintenance charge)” mode and keep the battery cartridge fresh and fully charged. Tips for maintaining maximum battery life 1. Charge the battery cartridge before completely discharged. Always stop tool operation and charge the battery cartridge when you notice less tool power. 2. Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life. 3. Charge the battery cartridge with room temperature at 10°C - 40°C (50°F - 104°F). Let a hot battery cartridge cool down before charging it. 001754 1 3 4 A B 2 1. Reversing switch 2. Switch trigger 3. Clockwise rotation 4. Counterclockwise rotation 001754 1 3 4 A B 2 1. Reversing switch 2. Switch trigger 3. Clockwise rotation 4. Counterclockwise rotation Switch action CAUTION: • Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released. To start the tool, simply pull the trigger. Release the trigger to stop. Reversing switch action CAUTION: • Always check the direction of rotation before operation. • Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool. This tool has a reversing switch to change the direction of rotation. Slide the reversing switch to the A position (appear “F” marking) for clockwise rotation or slide to the B position (appear “R” marking) for counterclockwise rotation. 21 3 4 21 3 4 1. Red mark 2. Screw 3. Number 4. Adjusting ring ASSEMBLY Overload protector The overload protector automatically cuts out to break the circuit whenever heavy work is prolonged. Wait 20 - 30 seconds before resuming operation. 001760 Adjusting the fastening torque The fastening torque can be adjusted infinitely from approx. 5 kg·cm (0.4 ft·lbs) to 37 kg·cm (2.7 ft·lbs). To adjust it, loosen the two screws and turn the adjusting ring. Then tighten the screws to secure the adjusting ring. Refer to the table for relation between the numbers on the adjusting ring and the fastening torque to be obtained. 001763 Numbers on Fastening torque to adjusting ring be obtained 1 5 kg·cm (0.4 ft·lbs) 2 10 kg·cm (0.8 ft·lbs) 3 18 kg·cm (1.3 ft·lbs) 4 27 kg·cm (1.9 ft·lbs) 5 37 kg·cm (2.7 ft·lbs) Example: 10 kg·cm (0.8 ft·lbs) of fastening torque can be obtained when the number 2 is aligned to the red mark. NOTE: • Always tighten the two screws to secure the adjusting ring after adjusting the fastening torque. CAUTION: • Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool. Installing or removing bit CAUTION: • Always be sure that the tool is switched off and the battery cartridge is removed ...