Votos - , Puntuación media:
(
)
)
Fabricar: Makita
Tamaño del archivo: 1.5 mb
Nombre del archivo: 6092D.pdf
Idioma del manual:
El documento se está cargando, por favor, espere
 |
El documento se está cargando, por favor, espere
Resumen del manual
A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user - a s well a s damage to the tool. If in doubt, DO NOT PLUG IN THE TOOL. Using a power source with voltage less than the nameplate rating is harmful to the motor. 3 IMPORTANT Length of Cord (Feet) AWG Size of Cord SAFETY 25 50 100 150 18 18 18 16 IN STRU CTI 0 N S 1. 2 . 3. 4. 5 . 6. 7. 8. SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for battery charger. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, ( 2 ) battery, and ( 3 ) product using battery. CAUTION - To reduce risk of injury, charge only MAKITA Battery 7000, 9000 or 9100. Other types of batteries may burst causing personal injury and damage. Do not expose charger to rain or snow. Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire, electric shock, or injury to persons. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when disconnecting charger. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress. An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock. If extension cord must be used, make sure: a. That pins on plug of extension cord are the same number, size, and shape b. That extension cord is properly wired and in good electrical condition; and c. That wire size is at least a s large a s the one specified in the table below. TABLE 1 RECOMMENDED MINIMUM AWG SIZE FOR EXTENSION CORDS FOR BATTERY CHARGERS a s those of plug on charger; 9. Do not operate charger with damaged cord or plug - replace them immediately. I O . Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified serviceman. 11. Do not disassemble charger or battery cartridge; take it to a qualified serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire. 12. To reduce risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning. Turning off controls will not reduce this risk. 4 ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) 2. Do not attempt to use a step-up transformer, an engine generator or DC power 3. Do not allow anything to cover or clog the charger vents. 4. Always cover the battery terminals with the battery cover when the battery 5 . A battery short can cause a large current flow, overheating, possible burns or ABOVE 4OoC (104OF). receptacle. cartridge is not used. and even a breakdown. (1) Do not touch the terminals with any conductive material. (2) Avoid storing battery cartridge in a container with other metal objects such (3) Do not expose battery cartridge to water or rain. ture may reach or exceed 5OoC (122OF). completely worn out. The battery cartridge can explode in a fire. a s nails, coins, etc. 6. Do not store the tool and Battery Cartridge in locations where the tempera- 7. Do not incinerate the Battery Cartridge even if it is severely damaged or is ADDITIONAL SAFETY RULES 1. Be aware that this tool is always in an operating condition, because it does 2. Always be sure you have a firm footing. 3. Hold the tool firmly. 4. Keep hands away from rotating parts. 5 . When drilling into walls, floors or wherever "live" electrical wires may be encountered, DO NOT TOUCH ANY METAL PARTS OF THE TOOL! Hold the tool only by the insulated grasping surfaces to prevent electric shock if you drill into a "live" wire. not have to be plugged into an electrical outlet. Be sure no one is below when using the tool in high locations. 6. Do not leave the tool running. Operate the tool only when hand-held. 7. Do not touch the drill bit or the workpiece immediately after operation: they may be extremely hot and could burn your skin. SAVE THESE INSTRUCTIONS. 5 Installing or removing battery cartridge 0 Always switch off the tool before insertion or removal of the battery cartridge. *To remove the battery cartridge, pull out I 0 the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the barrel. 1 To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Snap the set plate back into place. Be sure to close the set plate fully before using the tool. 0 Do not use force when inserting the battery cartridge. If the cartridge does not slide in easily, it is not being inserted correctly. Charging Plug the fast charger into your power source. Insert the battery cartridge so that the plus and minus terminals on the battery cartridge are on the same sides as their respective markings on the fast charger. Insert t...
Otros modelos de este manual:Taladros y shuropopverty - 60921 (1.5 mb)