Votos - 4, Puntuación media: 3.8
(
)
)
|
Resumen del manual
After charging, unplug the charger from the power source. CAUTION: Your new battery cartridge is not charged. You will need to charge it before use. If you try to charge a cartridge from a just-operated tool, sometimes the charging light will not come on. If this occurs, let the cartridge cool off for a while. Then re-insert it and try to charge it once more. 0 When you charge a new battery cartridge or a battery cartridge which has not been used for a long period, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharging it almost completely a couple of times. 0 If you wish to charge two battery cartridges, allow 15 minutes between chargings on the fast charger. Bit installation & removal CAUTION : Always set the Forward-Reverse switch lever to NEUTRAL when installing, removing or adjusting bits or accessories. Chuck When installing a drill bit, notice that there are three holes in the chuck at which you must use the key for tighten- ing. Insert the chuck key in any of the 3 holes and turn to the left (counterclock- wise) to release jaws of chuck. Insert the bit and tighten with chuck key to the right. Tighten evenly at all three holes in sequence. 1 Clip-on chuck key Overload protector The overload protector automatically cuts in to break the circuit and the button pops out, whenever heavy work is prolonged. Wait 20-30 seconds before pressing the restart button (on housing in back) to resume operation. Your finger should not be on the trigger when you press the restart button, however. Overload protector I" / Switch action Move the reversing switch lever to the & position for clockwise rotation or the position for counterclockwise. )J& To start the tool, simply pull the trigger. Release the trigger to stop. When the re- versing switch lever is in the neutral posi- tion, the tool will not start even if you pull the trigger Drill .Punch a small hole in the metal to pre- vent the bit from skitterring when start- ing to drill a hole. .Use machine oil on the bit to facilitate drilling. Reversing -switch lever 'rigger switch *Pressing down too hard on the tool will not speed up the drilling. In fact, this undue pressure will only serve to damage the tip of your drill bit, decrease your drilling per- formance and shorten the service of the tool. *There is a tremendous force exerted on the tool/bit at the time of hole break through. Grip the drill firmly and exert care when the bit begins to break through the materials. Screw Item Nominal Diameter (mm) *I Match your bit to your screw. 1. Phillips bits Bit No. Wood Screw Phillips bit No. 2 -45 mm is standard equipped. Select your screws and 2.1 -2.7 13/32" -lis") nominal diameter with the chart on the No. 2 3.1 -4.8 (118'' -3/16") right. 2. Slotted bits Unless you use a bit that fits properly the slot on the head of the screw, the slot will be damaged and the screw will not fasten. If the bit fails to match the slot, use a grinder or some such tool to trim the bit to fit the slot. NOTE : Rest the tool for 15 minutes when changing battery for continuous operation. 9 Grip .The grip shown on the right is recom- mended. However, grip the tool firmly with both hands when drilling a large- diameter hole. *The hole on the heel of the tool is a con- venient way to carry it by a cord, hook or other means. ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. Bits I I Size Part NO. #2 784214-0A Phillips 1 1 #?F 784011-0A Square drill bit 784606-0A I I 0 Tool holster has some bits storage space Use holster to carry drill only after removing bit. Also, keep the reversing switch lever in neutral position when carrying in the holster. Part No. 823033-3A Part No. 823033-3E (Genuine leather) 0 Battery holster Holds with extra battery Part No. 823033-3C 0 Rubber pad assembly Part No. 123001-2 8r T, ,P 0 Foam polishing pad Part No. 743023-2 0 Fast charger Model DC7100 Part No. 113086-6 0 Battery cartridge 7000 Part No. 632002-4 0 Chuck key S10 Part No. 763419-1 0 Wool bonnet Part No. 743401 -6 0 Plastic carrying case Part No. 824446-4 0 Keyless drill chuck Part No. 763083-8 0 Charger 12V for car Model DC7112 Part No. 113109-0 0 Battery cover Part No. 414938-7 Mar~-l1-'87 US 10 mm (318") CORDLESS DRILL Model 6010D Note: The switch and other part configurations may differ from country to country. MODEL 6010D Mar 11 87 EN 'Ff $:D DESCRIPTION ,",",, DESCRIPTION 1 1 Pan Head Screw M5x18 10 1 Housing Ser lWilh Item 271 2 1 Drill Chuck S10 12 1 Baffery 7000 3 1 Gear 13 1 Holder 6 4 1 Plane Bearing 5 14 1 Name Plate 5 1 DC Motor 7 2 V 16 7 Pan Head Screw M4x22 IWith Washer1 6 1 Plane Bearing 3 17 1 set Plate 7 1 Gear 13-58 25 1 Over Current Relay 8...
Otros modelos de este manual:Taladros y shuropopverty - 6OLODW (748.76 kb)