Votos - 3, Puntuación media: 4.7
(
)
)
|
Resumen del manual
Do not disassemble charger or battery cartridge; take it to a qualified serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire. To reduce risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning. Turning off controls will not reduce this risk. 4 ADDITIONAL SAFETY RULES FOR CHARGER AND TOOL 1 . The Charger and the tool are specifically designed to work together. Do not attempt to charge any other cordless tool with this Charger. Do not attempt to charge the tool with any other charger. 2. Do not charge the tool when temperature is BELOW 10°C ( 5 O O F ) or ABOVE 45OC (113°F). 3. Do not use charger in damp or wet locations. 4. Do not attempt to use a step-up transformer, an engine generator or DC 5. Do not store the tool in locations where the temperature may reach or exceed 6. Do not incinerate the tool even if it is severely damaged or is completely worn power receptacle. 5OoC (122OF). out. The tool can explode in a fire. ADDITIONAL SAFETY RULES FOR CORDLESS DRILL 1 . Be aware that this tool is always in an operating condition, because it does 2. Always be sure you have a firm footing 3. Hold the tool firmly. 4. Keep hands away from rotating parts. 5. When drilling into walls, floors or wherever "live" electrical wires may be encountered, DO NOT TOUCH ANY METAL PARTS OF THE TOOL! Hold the tool only by the plastic handle or plastic tool body to prevent electric shock if you drill into a "live" wire. not have to be plugged into an electrical outlet. Be sure no one is below when using the tool in high locations. 6. Do not leave the tool running. Operate the tool only when hand-held. 7. Do not touch the drill bit or the workpiece immediately after operation, they may be extremely hot and could burn your skin. SAVE THESE INSTRUCTIONS. 5 HOW TO USE Charging Connect the charging plug to the charging connector, then plug in the charger to the power receptacle. Charging takes 3 hours. CAUTION: The battery in your new tool is not fully charged. You will need to charge it be- fore use. Do not operate the tool during charging. Overcharging more than 2 days consid- erably shortens the battery service life. Always unplug the charger after completing the charge. When you charge a new tool or a tool which has not been used for a long period, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the tool fully after discharging it almost completely a couple of times. Installing and removing bit To install the drill bit, place it in the chuck as far as it will go. Tighten the chuck collar by hand. Place the cuck key in each of three holes, and tighten clockwise. To remove the drill bit, place the chuck key into the chuck hole and turn counterclockwise. CAUTION : Always set the Forward-Reverse switch lever to NEUTRAL when installing, removing or adjusting bits of accessories. 6 After use, return the chuck key to the storage cavity on the tool. I Switch action Set the reversing switch lever just in front of the trigger switch to Forward (FWD) or Reverse ( R E V ) . Then pull the trigger to t u r n the tool ON and release it to turn it OFF. To change the direction of bit rotation, release the trigger, let the tool come to a complete stop, and then slide the reversing switch lever to the opposite side. When the reversing switch lever is in the neutral position, the tool will not start even if you pull the trigger. CAUTIONS : When not operating the tool, keep the reversing switch lever in the neutral position. 0 Before operation, always check to be sure t h a t the reversing switch lever is set for the desired direction of rotation. 7 Holding tool Hold the tool as shown in the figure. When drilling a large diameter hole, the tool frimly with both hands. hold Drilling in metal Punch a small hole in the metal to prevent the bit from skittering when starting to drill a hole. Use cutting lubricant on the bitto facilitate drilling if necessary. Pressing down too hard on the tool will not speed up the drilling. In fact, this undue pressure will only serve to damage the tip of your drill bit, decrease your drilling performance and shorten the service life of the tool. There is a tremendous force exerted on the tool/bit at the time of hole break through. Grip the drill firmly and exert care when the bit begins to break through the material. 8 Screwdriving Match your bit to your screw. ~~ Item I Nominal Diameter (mm) Bit No. Wood Screw 2.1 - 2.7 (3132" - 118") 1. Phillips bits Select your screws and nominal diameter with the chart on the right. No. 2 3.1 - 4.5 (118" - 3/16") 2. Slotted bits Select a slotted bit to match the slot on the screw heads. If the bit is too small for the screw slot, the bit and/or screw head may be damaged. Overload protector The overload protector automatically cuts out to break the circuit whenever heavy work is prolonged. Wait 20-30 seconds before resuming ...
Otros modelos de este manual:Taladros y shuropopverty - 6OLOSD (1.25 mb)