Votos - 3, Puntuación media: 3.7 ( )

Fabricar: Black & Decker Tamaño del archivo: 3.45 mb Nombre del archivo: Idioma del manual:

SCREWDRIVER ACCESSORIES 6* Hex Bit Extension For use with 1/4" Hex Shanks and/or other extensions. 1/4* oit ««re Drive Magnetic Socket For driving 8 Pointed Nylon and Steel Headed Screws. Heavy-Duty Tool Box Cat. No. 50078 I Scrugun® Holster Cat. No. 69590 attaches tobelts up to 2-3/4" wide. Magnetic Bit Tip Holders for Dry wall Scruguns 1/4" Hex Shank for 1/4" Hex Tip (3-3/32 long) for use with all Drywall SCRUGUNS® EXTRA LENGTH BIT TIP DRIVE BODY. 1/4* Hex Shank for 1/4" Hex Tip (2-31/32 long) for use with all Drywall SCRUGUNS® STANDARD LENGTH STAINLESS STEEL BODY. (Standard equipment on H.D. drywall SCRUGUNS®) BELT CLIP Cat. No. 69600 For all H.D. SCRUGUN Screwdrivers. (Standard equipment on H.D. drywall SCRUGUNS*) 7 VERSA-CLUTCH FOR DRIVING A WIDE RANGE OF FASTENERS RPM NOMINAL CAPACITY SELF THREAD SHEET WOOD LAG DRILL CUTTING METAL MACHINE SCREWS SCREWS SCREWS SCREWS SCREWS SCREWS 0-1200 #12 1/4" w/pilot hole 1/4" 1/4" 1/4* 1 4' 3/16" CRS 1. Install proper fastener driving accessory and set screwdriver for ■ correct rotation, 2. Adjust clutch setting. See Fig. 4. 3. Place fastener in accessory, contact workpiece and apply pressure to seat fastener keeping clutches engaged. 4. Upon fastener seating the clutches will ratchet. Disengage screwdriver from fastener. NOTE: With Versa-Clutch the operator has the ability to “override” clutch ratchet if a fastener hits a wood knot, variable hardness in steel workpieces or incorrect pilot holes. Increased operator pressure will usually cause the clutches to "pick-up*’ and continue to seat the fastener. Further, a quick twist of the collar will change the clutch setting to overcome most driving difficulties and will provide for immediate change in torque output giving the operator option to drive a range of fastener sizes. MAINTENANCE CLEANING With the motor running, blow dirt and dust out of all air vents with dry air at least once a week. Wear safety glasses when performing this. Exterior plastic parts may be cleaned with,a damp cloth and mild detergent. Although these parts are highly solvent resistant, NEVER use solvents. 1. Remove clutch housing by unscrewing in direction of arrow (left hand thread). 2. Clamp tool or clutch housing in a resilent clamp. 3. Remove round clutch retaining rings - with a very small screwdriveror sharp pointed tool. 4. Install new clutches and new retaining rings. NOTE : If the output spindle slides toward inside of gear case, remove dead spindle spring and thread a 5/16" -.18 bolt or cap,screw into end of spindle and lift up to expose retaining ring, groove. Re-assemble dead spindle spring allowing no more than 1/4* projecting from end of spindle. 5. Relubricate clutches, (See lubrication ' CHANGING CLUTCHES (Fig. 7) FOR VERSA-CLUTCH ONLY CHANGING CLUTCHES (Fig. 8) FOR POSITIVE CLUTCH & DRYWALL UNITS ONLY CLUTCH OUTPUT SPINDLE RETAINING RING GEAR CASE- Figure 8 1. Remove three gear case screws from front and disassemble . gear cas...

Descargar ahora

Introduzca dos números de la imagen: