Votos - , Puntuación media: ( )

Manual de usuario Craftsman, modelo 315.111450

Fabricar: Craftsman
Tamaño del archivo: 790.29 kb
Nombre del archivo:

Idioma del manual:

El documento se está cargando, por favor, espere

Descargar ahoraCerca

El documento se está cargando, por favor, espere

Descargar ahoraCerca

Therefore, you should charge tt at least 5 hours prior to use NOTE:Your drill wltl not reach fult charge the first ttme it is charged. Allow several cycles (drilling followed by recharging) for your drill to become fully charged, DRILL SELECTOR SWITCH TRIGGER WRIST STRAP TO CHARGE 1, Connect charger to your drill by inserting charger plug Into input jack, NOTE: As shown In Figure 1, input Jack is located at the rear of toot 2 Charger can be used with normal house voltage of 110.120 volts, 60 Hz. AC only. 3, Connect charger Io power supply NOTE: The LED indicator, which is located above the switch, will iight up when charger is properly con. nected to power supply Thts light indicates your drill is charging and will rematn on until charger ts disconnected from power supply. NOTE: Do not operate your drill while it is connected to the charger. The driving ability of your drill will not increase, NOTE: After normal usage, your drtlI usually requires 3 hours of charging time to be fully charged YOUR DRILL _ONTAINS SPECIAL HIGH TEMPERATURE BATTERIES TO HELP PRE VENT BATTERY DAMAGE WHEN LEFT ON CHARGE FOR EXTENDED PERIODS OF TIME, HOWEVER, ONCE THE BATTERIES OF YOUR DRILL BECOME FULLY CHARGED, WE RECOMMEND THAT YOU UNPLUG YOUR CHARGER FROM POWER SUPPLY THEN DISCONNECT THE CHARGER FROM YOUR DRILL.. UT JACK CHARGER PLUG LED INDICATOi_i// BATTERY CHARGER l Page 5 OPERATION (Cont.) BATTERIES Your ddtl is equipped with 5 nickel-cadmium rechargeabte batteries Length of service from each charging will depend on the type of work you are do ing '[he nickel,.cadmium batteries in this tool have been designed to last for the life of the unit under normal operating conditions. Therefore, do not disassemble your drill and attempt to replace them, Handling of these batteries, especially when wearing rings and jewelry, could result in a serious burn WRIST STRAP A wrist strap ts provided to reduce the chances of dropping your drill, Place one hand through wdst strap when carrying your dr_il See Figure 4. SWITCH The switch on your drill is designed for single speed drilling For normal drilling operatfon, depress the switch trigger atl the way. REVERSIBLE Your dri!l has the feature of being reversible The direction of rotation is controlled by a selector located above the switch trigger. See Figure 2. With your drill he{d in normal operating position, the direction of rotor{on selector should be positioned to the left of the switch for drilling The drill direction Is reversed when the selector is to the right of the switch When the selector is in center position, the switch trigger Is locked,, TO PREVENT GEAR DAMAGE, ALWAYS ALLOW THE CHUCK ON YOUR DRILL TO COME TO A COMPLETE STOP BEFORE CHANGING THE DIRECTION OF ROTATION. To stop your drill release switch trigger and allow your drill to come to a complete stop. NOTE: To lock switch trigger, place the direction of rotation selector in center position. See Figure 2 CHUCK KEY A chuck key has been packed with your drill for use when installing or removing bits tt is also used when removing the chuck See Figure 3 CHUCK KEY STORAGE When not in use the chuck key can be placed in the storage area located on the back of your ddt! See Figure 3 FORWARD REVERSE SELECTC SWITCH TRIGG ER POSITION (LOCK,OFF) Fig, 2 CHUCK KEY STORAGE CHUCK KEY Fig 3 Page 6 OPERATION (Cont.) INSTALLING BITS ----.... 1 Lock switch trigger on your ddtt by placing the direction of rotation selector in center position. 2 Close chuck jaws to a point where the opening is slightly larger than the bit size you intend to use, 3 insert your drilJ bit into chuck the full length of the jaws as shown in Figure 4, BIT 4" Remove chuck key from chuck key storage See Figure 3 5 Tighten chuck jaws by placing chuck key tn each o! the three holes, and tighten in a clockwise direction. DO NOT USE A WRENCH TO TIGHTEN OR LOOSEN THE CHUCK, 6. Remove the chuck key and return to chuck key storage REMOVING BITS t. Lock switch trigger on your dri]! by placing the direction of rotation selector In center position 2 Remove chuck key from chuck key storage, See Figure 3 3 Loosen chuck jaws using the chuck key, DO NOT USE A WRENCH TO TIGHTEN OR LOOSEN THE CHUCK,, 4. Remove drill bit from chuck jaws., 5 Remove chuck key and return to chuck key storage, CHUCK REMOVAL The chuck must be removed in order to use some accessories To remove: 1 LOck switch trigger on your drill by placing the direction of rotation selector in center position 2 Remove chuck key from chuck key storage See Figure 3 3. Close the chuck jaws. Insert chuck key into chuck and tap sharply with a mallet in a clockwise direction as shown in Figure 5 4, Open the chuck jaws and remove the chuck screw by turning it in a clockwise direction See Figure 6 NOTE: The chuck screw has left hand threads 5. Inserl the chuck key in chuck and tap sharply in a counterclockwise direction to loosen it on spin. die, I1 can now be unscrewed by hand, See Figure 7, 6 Return chuck key to chuck key storage...