Votos - 1, Puntuación media: 5
(
)
)
|
Resumen del manual
Do not use the angle vise for milling. It is made strictly for holding materials to be drilled. This vise will not adequately clamp an object safely for a milling operation. There is not enough clamping pressure available and objects may be pulled out or upset in the vise jaws causing cutting tools to break and/or parts to be thrown. Any attempt to perform a milling operation using this vise may result in personal injury. DO NOT make adjustments while the Mill/Drill is running. Ensure that the switch is off, power is disconnected and moving parts have stopped before making adjustments. With the head fully raised, this unit is very top heavy and will tip over if not bolted down. Tipping can cause a pinch or crushing type injury. Secure the base firmly. -11-G1006/G1007 Mill/Drill Power feed The Model G1007 features a 110V auto-feed mechanism which allows hands-free, side-to-side passes while milling. Variable-speed feed control makes flat surface milling more consistent. To install the power feed: 1. Attach the 21/4" diameter drive gear to the left end of the longitudinal table leadscrew. The setscrew for securing the drive gear requires a 2.5mm Allen® wrench. The gear couplers on the drive gear and table lead- screw will lock together. 2. Set the clamping bracket assembly on the left end of the table. Mark the points on the table’s trough where the mounting bolts contact the table. Remove the clamping bracket assembly and spot drill to give the mounting bolts a small lip to “bite” without slipping on the rough cast surface. Set the clamping bracket assembly back on the end of the table and tighten down the mounting bolts. 3. Use a 5mm Allen® wrench to attach the power feed body to the clamping bracket assembly. Cap screws are provided. Before tightening completely, position the power feed body so the gears mesh perfectly. Tighten the cap screws when the gears are in mesh. NOTICE Use care when aligning the table lead- screw gears with the gearing on the power feed. The fit is correct when you can just slightly wiggle one gear without engaging the other. If there is too much space between the gears, teeth can be stripped under heavy loads. If the teeth mesh too tightly, the supporting bearings in the power feeder will wear out quickly. 4. Plug the rapid switch cord into the receptacle provided on the bottom of the power feed body. 5. Screw the knob onto the direction handle. 6. Place the clear plastic gear cover to the bottom of the power feed to protect the gears. 7. Insert the stops into the slot on the front edge of the table. Tighten them with a 5mm Allen® wrench. NOTICE Before using the G1007, place the power feeder cord and the control cord for the microswitch clear of any movements which could pinch or crush them. Before using the power feed, mark the maximum distance the table can move before the power feed comes in contact with the machineOs base. Use that mark as a reference each time you re-adjust your table stops. This is the best way to avoid damaging the power feed and/or causing an unsafe condition. 8. Remove the center travel stop at the front of the table. Save the mounting bolts. 9. Secure the switch bracket to the front of the Mill/Drill. Use the mounting bolts saved in step 8. 10. Mount the switch to the switch bracket using the cap screws provided. Tighten them with a 6mm Allen® wrench. When the switch is depressed, the power feed automatically turns off and table movement stops. -12 G1006/G1007 Mill/Drill Handwheels/Crank There are three handwheels provided with the machine which control table movement. They are secured with setscrews and mounted as follows. Height adjustment is made using the crank provided. Each handwheel has a setscrew which tightens with a 3mm Allen® wrench. The handwheel handles screw into the threaded holes on each hand- wheel. Turn the nut on the handwheel handles until almost tight against the plastic handle. Screw into the handwheel and tighten the nut against the wheel while maintaining the screw’s position with a screwdriver. This nut acts as a locknut and a spacer. The first two handwheels mount on the ends of the table and move the table left and right. With the power feed installed on the G1007, there is only one side handwheel installation location. Save the extra handwheel in case the power feed cannot be used. The third handwheel mounts in front of the base and moves the table toward and away from the front of the machine. The head crank secures to the left side of the machine. Screw its handle into the threaded hole at the end of the crank. This handle is similar to those in the handwheels. Use a 5mm Allen® wrench to tighten the setscrew that secures the hand crank to its shaft. Screw a black knob onto an end of each of the three chrome feed levers. These are the levers that control the up and down movement of the spindle. Screw the levers with knobs into the threaded holes on the hub, located on the right side of the machine. Collet/Arbor The Models G10...
Otros modelos de este manual:Taladros y shuropopverty - G1007 (517.79 kb)