Votos - 3, Puntuación media: 5
(
)
)
|
Resumen del manual
Model g5789/g5790 inventory. Model g5789/g5790 13-piece 3.4" impact wrench Kit -3 -4- Model G5789/G5790 13-Piece 3.4" Impact Wrench Kit OPERATIONS ACCIDENTAL START HAZARD ! Disconnect before service or tool changes. AIR PRESSURE HAZARD ! Never exceed 120 PSI . LUNG /EAR IN JURY HAZARD ! Wear protective equipment when using this tool. Read the manual before operation. Become familiar with this tool, its safety instructions, and its operation before beginning any work. Serious personal injury may result if safety or operational information is not understood or followed. G5789 Specifications Drive Size................................................ 3.4" No-Load Speed......................... 4,500 RP M Maximum Torque........................... 500 ft/lb Air Inlet Size.......................... 3.8" or 1.4" NPT Air Consumption............................... 7 CFM Operating Pressure.......................... 90 PSI Maximum Operating Pressure....... 120 PSI Weight...............................................9.9 lbs G5790 Specifications Drive Size................................................ 3.4" No-Load Speed......................... 4,500 RP M Maximum Torque........................... 500 ft/lb Air Inlet Size.......................... 3.8" or 1.4" NPT Air Consumption............................... 7 CFM Operating Pressure.......................... 90 PSI Maximum Operating Pressure....... 120 PSI Weight...............................................9.9 lbs EYE IN JURY HAZARD ! Wear protective equipment when using these tools. The impact wrench requires 90 PSI to operate correctly. To improve air tool lifespan, use a filter/lubricator/regulator setup shown in Figure 2. Quick Connector Quick Coupler Air Hose Quick Coupler Quick Connector Lubricator Filter Regulator Air Compressor Your Tool Figure 2. Installed filter lubricator regulator. Air Supply otherwise, lubricate the impact wrench to change the direction of rotation, push daily with a 2–6 drops of pneumatic tool the reverse valve toward the front of the oil directly into the tool's air inlet fitting, as gun for clockwise rotation and to the rear shown in figure 3, before and after each for counterclockwise rotation. to change the direction of rotation, push daily with a 2–6 drops of pneumatic tool the reverse valve toward the front of the oil directly into the tool's air inlet fitting, as gun for clockwise rotation and to the rear shown in figure 3, before and after each for counterclockwise rotation. use and every 2 hours of continued use. figure 3. Manual oiling. impact Wrench your new 3.4" drive impact wrench (figure 3) will generate up to 500 ft/lbs. of torque. only use thick-walled impact sockets with this air tool. the common thin-walled chrome sockets may explode if used as impact sockets, causing serious injury. the impact wrench comes with a 3.8"–1.4" npt adapter. For maximum results, we recommend using a 3.8" air fitting and hose. to change the torque setting, turn the torque setting knob from 0 to 9; 9 is the highest torque setting. reverse Valve torque setting figure 4. impact wrench control locations. daily maintenance these procedures should be done after each use: • Before putting the impact wrench away, put 2-6 drops of oil into the air supply fitting and momentarily operate the tool to distribute the oil inside. • wipe the tool exterior and sockets with a slightly oiled cloth. your goal is to leave a light film of oil on the tool to prevent rust. Model g5789/g5790 13-piece 3.4" impact wrench Kit -5 g5789 impact Wrench .............................................................................................................................. ...................................................................................................... REF PART # DESCRIPTION REF PART # DESCRIPTION 1 P8125001 HOUSING 2 P8125002 VALVE SLEEVE 3 P8125003 REVERSE VALVE 4 P8125004 TRIGGER 5 P8125005 ROLL PIN 6 P8125006 VALVE BUSHING 7 P8125007 O-RING 8 P8125008 STEEL BALL 9 P8125009 COMPRESSION SPRING 10 P8125010 AIR FITTING 3/8"-1/4" NPT 11 P8125011 AIR VALVE KNOB 12 P8125012 O-RING 13 P8125013 SET SCREW 14 P8125014 SPACER 15 P8125015 OIL SEAL 16 P8125016 PILOT SET SCREW 17 P8125017 ANVIL BUSHING 18 P8125018 ANVIL 3/4" DRIVE 19 P8125019 HAMMER CAGE 20 P8125020 HAMMER PIN 21 P8125021 HAMMER DOG 22 P8125022 DRIVE CAM 23 P8125023 O-RING 24 P8125024 CYLINDER 25 P8125025 ROTOR 26 P8125026 ROTOR BLADE 27 P8125027 FRONT PLATE 28 P8125028 BEARING 29 P8125029 REAR PLATE 30 P8125030 WASHER 31 P8125031 COMPRESSION SPRING 32 P8125032 PIN 33 P8125033 REAR GASKET 34 P8125034 REAR COVER 35 P8125035 CAP SCREW 36 P8125036 LOCK WASHER 37 P8125037 OIL SEAL 38 P8125038 FRONT RUBBER 39 P8125039 EXHAUST DEFLECTOR 40 P8125040 ANVIL COLLAR 42 P8125042 PHLP HD SCREW 43 P8125043 RUBBER BUSHING 44 P8125044 REAR RUBBER 45 P8125045 SET SCREW 46 P8125046 ROLL PIN 48 P8125048 SPECIAL CAP SCREW *49 P8125049 O-RING KIT 50 PAW05M HEX WRENCH 5MM 51 PAW04M HEX WRENCH 4MM 52 P5789052 1/...
Otros modelos de este manual:Taladros y shuropopverty - G5789 (587.27 kb)