Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
Try to keep this ratcheting to a minimum for longest clutch life and longer screwdriving capacity between charges. Always drill pilot holes for wood screws. Spraying all screws with a dry lubricant will glm them the east©«! rundown. Experiment with different types of sheet metal screws to find the ones best syited to your application. pi©«* ? ADJUSTING DEPTH — PEPTH-SSfiSnWI 8CRUQUMS; 1. Pull back Collar and screw Locator in or out as follows: a) For DrywaiS Screws, end of bit should extend approximately 3/16* beyond end of Locator. b) For Washer Hex Head Screws, the nut setter should be approximately flush with end of Locator. c) For large Washer Head and “Sealer” Screws, the nutsetter should be recessed about 1/16* into Locator. 2. Make sure notches in Locator engage with pins In Collar. 3. Test drive a fastener in scrap material to determine if fastener is seating correctly. 4. Further fine adjustment may be necessary to increase or decrease fastener depth. Each notch setting change represents a .0083* change in depth setting (.050* for one complete revolution). LOCATOR FIGURE 8 ACCESSORIES CAUTION; We strongly recommend that your first purchase be the No. U2106 Safety Glasses which should be worn when, using all screwdriver accessories. The accessories listed in this manual are available at extra cost from pur local dealer or Black & Decker Service Center. A complete listing of service centers is included on the owner’s registration card packed with your tool. If you need assistance in locating any accessory* please contact: Black ' & Decker (U.S.) Inc., User Services Department, 626 Hanover Pike, P.O. Box 618, Hampstead, Maryland 21074=0618. Recommended accessories for your Tool are shown in this manual. The use of any other accessory might be hazardous. 1/4" HEX SHANKS four' Scrugun® can use practically every type of fastening accessory that has a 1/4* hexagon shank. BIT TIP HOLDERS 1 Non-Magnetic, For 1/4" Bit Tips • .■ Magnetic, For 1/4” Bit Tips HIM SHANK INSERT BITS FOR BIT TIP HOLDERS 120 VAC COMPUTERIZED 1 HOUR CHARGER ORDER CAT. NO. 98060 Screw Type Point Size (in.) Phillips 2 drywall Frearson Reed & Prince 6 & larger Phillips 2 Posidrive 3 Socket Hoad 1/8 Cap Screw 5/32 3/16 HEX SHANK POWER BITS Screw Type Point Size . Length (in.) Phillips О 2 2 3 1 15/16 3% 1 15/16 Phillips Posidrive О 2 3 1 15/16 1 15/16 1/4" HEX DRIVE NU* For driving Imk head rSETTERS fastener _I o Type Socket Size (in.) Length (in.) Non- Magnefic 1/4 5/16 3/8 2 9/16 2 9/16 2 9/16 Magnetic 1/4 1/4 5/16 3/8 1 5/8 2 9/16 2 9/16 2 9/16 1/4" HEX BIT WITH ROTATING FINDER BIT Length Gen. Screw Sizes 3-1/2* -, 3-1/2* 4, 5 5, 6, 8 Й in 3-1/2" 3-1/2" 8, lu 8, 10 12 HOLSTER To add even more to the convenience features of your Cordless Drill, an accessory Holster is available. This Holster fastens to your belt and keeps the Drill handy and ready for work. It also frees both hands when you are not actually using the tool. Order: Cat. No. 98004 Holster 12 VOLT DC COMPUTERIZED 1 HOUR CHARGER ORDER CAT. NO. 98065 FOR CARS OR TRUCKS No. 98003 Fast Charge Energy Pack CLEANING & LUBRICATION Use only mild soap and a damp cloth to clean the tool. Many household clean« m-. < «>ni.nn <;h< nnicals which could seriously damage the plastic. Also, do not use gasoline, turp^ntino, Ucquor or paint thinner, dry cleaning fluids or similar products. Never let any liquid get inside the tool; n< *v< [ immerse any part of the tool into a liquid. Self lubricating bearings are used in the tool and periodic relubrication is not required, Howevor, it is recommended that, once a year, you take or send the tool to a B&D Service Center for a thorough cleaning, inspection and lubrication of the gear case. NOTE: The metal contacts of the Power Pack may corrode slightly after a period of time. 11 ihis occurs, remove the deposits with a soft cloth or standard pencil eraser. STORAGE 1. The best storage place is one that is cool and dry—away from direct sunlight, heating pipes or ducts, furnaces, etc. Power Packs should not be stored in a position where their contacts could touch metal objects. 2. Best storage temperature is approximately +50°F. Do not store where temperatures may go below +40°F or above +120°F. Avoid storage in outside metal buildings where the temperature could go above +120°F in summer, as this could damage the power pack. 3. Long storage will not harm the Scrugun, Power Pack or Charger. Under the proper conditions (given above) they can be stored for 5 years or*more without harm. IMPORTANT To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment, (including brush inspection and replacement) should be performed by Black & Decker Service Centers or other qualified service organizations, always using Black & Decker replacement parts. Power pack battery replacement should be accomplished at B&D Service Centers, using only identical replacement...