Votos - 2, Puntuación media: 3
(
)
)
|
Resumen del manual
1 2 3 1 2 5 FIGURE 4. INSTALLING THE DRILL PRESS AND MOTOR FIGURE 5. INSTALLING HANDLES 4 2 3 1 4 2 1 3 FIGURE 6. INSTALLING THE DRILL CHUCK LASER GUIDE Use of controls or procedures, or performance of procedures other then those specified herein may result in hazardous radiation exposure. LASER SAFETY NEVER LOOK INTO THE LASER BEAM. Any contact with the eyes by the beam could cause injury. Do not use the laser when cutting reflective materials. DO NOT AIM THE LASER BEAM AT ANYONE OR AT REFLECTIVE SURFACES. CLASS 2M LASER PRODUCT. Any contact with the eyes by the beam could cause injury. Ensure the laser beam is turned on only when the tool is on a nonreflective workpiece and as such it is aimed only at the work surface. Metals and other materials like steel which can be highly reflective should only be cut without the use of the laser. To avoid damage to the drill chuck and the spindle shaft, do not drive the chuck onto the spindle shaft with a metal hammer. Damage to the Drill Chuck will occur. REMOVING AND INSTALLING DRILL BITS Disconnect drill press from AC power source and ensure the “ON/OFF” switch is in the “OFF” position. Failure to adhere to this warning could cause severe, permanent injury to the operator. Use only the chuck key provided by the manufacturer with the drill press. 1. Use the chuck key (1) to loosen the drill chuck (2). See Figure 7. 2. Insert the smooth end of the drill bit (3) into the drill chuck (2) as far as it will go. 3. Back the drill bit (3) out approximately 1/16" or up to the flutes for smaller bits. 4. Ensure the drill bit (3) is centered in the drill chuck jaws before tightening. 5. Use the chuck key (1) and tighten the drill chuck (2) locking the drill bit (3) in place. IMPORTANT: Lock all three jaws in the drill chuck bit to ensure proper tightening and so it doesn’t slip while drilling. 6. Ensure the check key (1) is removed from the drill chuck BEFORE applying power to the drill press. 7. The chuck key is equipped with a self-ejecting pin (4) that helps minimize the hazard of the key being inadvertently left in the drill chuck. 15 MOUNTING THE DRILL PRESS During operation of the drill press, there may be instances where the tool could tip over, slide, or walk on the supporting surface. To secure the drill press: 1. Place the drill press (1) on the workbench (2) as desired. 2. Secure the drill press (1) to the workbench (2) using two carriage bolts (3), flat washers (4), and nuts (5) through the holes in the drill press base. See Figure 8. 2 1 3 4 5 FIGURE 8. MOUNTING THE DRILL PRESS 3 1 3 2 4 FIGURE 7. INSTALLING DRILL BITS 17 18 STORE OUT OF REACH OF CHILDREN. Equipment should be in a high location or locked up to keep out of reach of children. It is not a toy. DO NOT TAMPER WITH THE LASER OUTPUT. Changing the performance of the laser to increase its output is prohibited. Any claim for damages or injuries resulting from not following these instructions will be refused. OPERATION ACCESSIBLE FIELDS: Wavelength 636-660nm Laser Power for Classification <1mW CW NEVER OPERATE LASER IF THE UNIT IS DEFECTIVE OR THE COVER OR SEAL IS DAMAGED. DO NOT SERVICE LASER. The laser unit must be returned to the factory for any service or repair. Service or repair must be handled by authorized factory trained technicians. Do not open the laser unit except to change batteries. REMOVE BATTERIES IF THE LEVEL IS TO BE STORED FOR ANY LENGTH OF TIME. Batteries may leak and damage the laser if it is stored idle for more than 3 months. Be careful with this tool. Striking or jarring it, especially on the laser housing, can affect its accuracy. Other than batteries, there are no user-serviceable parts in the laser device. OPERATING THE LASER Do not stare directly into the Laser beam, aperture or into a reflection from a mirror-like surface. The laser runs on two AAA batteries which are located beneath the “ON/OFF” switch. When the laser light begins to dim, change both batteries. NEVER mix old batteries with new. TO CHANGE LASER BATTERIES: 1. Turn off the laser. 2. Press the tab (1) located below the laser switch (2) and lift up the laser switch cover. 3. Insert two “AAA” batteries in the laser battery compartment (3). 4. Close the laser switch cover. USING THE LASER LIGHT: 1. Place the workpiece on the table. 2. Turn the laser switch to the ON position. 3. Lower the drill bit to meet the workpiece. The two laser lines should cross where the drill meets the workpiece. 4. If the drill needs to be adjusted: • Using a 3mm hex key, turn the laser adjustment set keys counter-clockwise. • Rotate the laser light housing until the two laser lines intersect where the drill meets the workpiece. DO NOT stare directly at the laser lines. 5. Re-tighten the adjustment set screws. AVOID EXPOSURE LASER RADIATION CA UTION AVOID EXPOSURE LASER RADIATION C AUTION 1 (ON/OFF SWITCH) (LASER APERTURES) 2 3 FIGURE 9. INSTALLING LASER BATTERIES CAUTION LABEL CAUTION LABEL LASER LIGHT DO NOT VIEW DIRECTLY WITH OPTICAL IN...
Otros modelos de este manual:Taladros y shuropopverty - 840116 (920.68 kb)