Votos - 3, Puntuación media: 4.3 ( )

Fabricar: Hotpoint-Ariston Tamaño del archivo: 1.66 mb Nombre del archivo: Idioma del manual:

The two appliances should be connected separately, and each one should have its own stop tap in order to make them completely independent from one another (see figures). I Connection with a rigid pipe (copper or steel) ! Connection to the gas system must be carried out in such a way as not to place any strain of any kind on the appliance. There is an adjustable L-shaped pipe fitting on the appliance supply ramp and this is fitted with a seal in order to prevent leaks. The seal must always be replaced after rotating the pipe fitting (the seal is provided with the appliance). The gas supply pipe fitting is a threaded 1/2 gas cylindrical male attachment. Connecting a flexible jointless stainless steel pipe to a threaded attachment The gas supply pipe fitting is a threaded 1/2 gas cylindrical male attachment. These pipes must be installed so that they are never longer than 2000 mm when fully extended. Once connection has been carried out, make sure that the flexible metal pipe does not touch any moving parts and is not compressed. ! Only use pipes and seals that comply with current National regulations. Checking the tightness of the connection ! When installation has been completed, check the pipe fittings for leaks using a soapy solution. Never use a flame. Adapting to different types of gas In order to adapt the oven to a type of gas other than the type for which it was manufactured (indicated on the label), follow these simple steps: • Replacing the oven burner nozzle 1. Open the oven door fully. 2. Slide out the bottom of the oven. 4 3. Unscrew the burner fastening screws. 4. Remove screw “V” and then the oven burner. 5. Unscrew the oven burner nozzle using the special socket spanner for the nozzles, or better still a 7 mm socket spanner, and replace it with a nozzle suited to the new type of gas (see Table 1). 6. Replace all the parts, following the steps described above in the reverse order. ! Take particular care when handling the spark plug wires and the thermocouple pipes. • Primary air regulation for the oven burner The burner was designed not to need any adjustments to the primary air. • Setting the oven burner to minimum 1. Turn the knob first to the Max setting for about 10 minutes and then to Min. 2. Remove the knob. 3. Remove the disk fastened to the control panel. 4. Adjust the screw located outside the thermostat cock pin until the flame is small but steady (the flame can be seen through the slots on the oven bottom). 5. Make sure the burner does not switch off when you turn the knob from Max to Min quickly, or when you open and close the oven door quickly. ! If the appliance is connected to liquid gas, the regulation screw must be fastened as tightly as possible. ! Once this procedure is finished, replace the old rating sticker with one indicating the new type of gas used. This sticker is available from any of our Service Centres. ! If the gas pressure is different from the recommended pressure, a suitable pressure regulator must be fitted to the inlet pipe in accordance with current National Regulations. Ф АЮ77 DATA PLATE width 43.5 cm Dimensions height 31 cm depth 43.5 cm Volume 58 l Electrical connections see data plate Gas features see data plate This appliance conforms to the following European Economic Community directives: 2006/95/EEC dated 12/12/06 (Low Voltage) and subsequent amendments - 2004/108/EEC dated 15/12/04 (Electromagnetic compatibility) and subsequent amendments - 93/68/EEC dated 22/07/93 and subsequent amendments. 90/336/EEC dated 29.06.90 (Gas) and subsequent amendments. 2002/96/EC and subsequent amendments. 5 Description of the appliance Overall view Control panel 6 Start-up and use ! The first time you use your appliance, heat the empty oven with its door closed at its maximum temperature for at least half an hour. Ensure that the room is well ventilated before switching the oven off and opening the oven door. The appliance may produce a slightly unpleasant odour caused by the burning away of protective substances used during the manufacturing process. Starting the oven This knob is used not only to select the different oven modes, but also to choose the right cooking temperature for various foods from among the temperatures shown on the knob itself (the range is from 140°C to 240°C inclusive). The electronic ignition device of the oven is built into the control knob. To light the oven burner, press the OVEN knob in as far as possible and turn it anti-clockwise, setting it to position 1 (keeping the oven door shut). The oven is equipped with a safety device. After lighting the burner allow the gas to circulate until the safety thermocouple is heated by keeping the OVEN knob pressed in for about 6 seconds. ! The electronic ignition device of the oven burner must not be activated for more than 15 seconds. If the burner fails to light after 15 seconds, stop pressing the OVEN knob, open the oven door and wait for at...

Descargar ahora

Introduzca dos números de la imagen: