Votos - 0, Puntuación media: 0 ( )

Fabricar: Bosch Tamaño del archivo: 1.24 mb Nombre del archivo: Idioma del manual:

With both hands, grip the door on the left and right-hand sides. Close the door a little further and pull it out ( figure B) . . . Attaching the door Reattach the oven door in the reverse sequence to removal. 1. When attaching the oven door, ensure that both hinges are inserted straight into the opening (figure A). 2. The notch on the hinge must engage on both sides ( figure B) . 3. Fold back both locking levers (figure C). Close the oven door. a= Risk of injury! If the oven door falls out accidentally or a hinge snaps shut, do not reach into the hinge. Call the aftersales service. Removing and installing the door panels To facilitate cleaning, you can remove the glass panels from the oven door. Removal 1. Detach the oven door and lay it on a cloth with the handle facing down. 2. Unscrew the cover at the top of the oven door. To do this, undo the left and right screws (fig. A). 3. Lift the top panel up and out ( fig. B) . 4. Unscrew the retaining clips on the right and left. Lift the panel and remove the brackets from the panel ( fig. C). Take out the panel. Clean the panels with glass cleaner and a soft cloth. Do not use sharp or abrasive materials or a glass scraper. This may damage the glass. Fitting When fitting, make sure that the lettering " right above" is upside down at the bottom left. 1. Insert the panel diagonally towards the back (fig. A). 2. Stick the retaining clips onto the right and left-hand sides of the panel, aligning them so that the carriers are over the screw holes, and then screw in place (fig. B) . 3. Insert the uppermost panel diagonally towards the back. The smooth surface must face outwards. 4. Put the cover back in place and screw it on. 5. Attach the oven door. Do not use the oven again until the panels have been correctly fitted. Troubleshooting Malfunctions often have simple explanations. Refer to the table before calling the after-sales service as you may be able to remedy the fault yourself. Malfunction table If a dish doesn't turn out as well as you had hoped, refer to the section Tested for you in our cooking studio, where you will find plenty of cooking tips and tricks. Problem Possible cause Remedy/ information The oven does The circuit Look in the fuse box and not work. breaker is check that the circuit defective. breaker is in working order. Power cut Check whether the kitchen light or other kitchen appliances are working. 0 and zeros Power cut Reset the clock. light up in the display. The oven does There is dust on Turn the control knobs back not heat up. the contacts. and forth several times. Error messages If an error message with “ appears, press the 0 button. The message disappears. A time function that has been set is cleared. If the error message does not disappear, please contact the after-sales service. You can take remedial action yourself if the following error message is displayed. Error message Possible cause Remedy/ information “‹ ‚ ‚ A button was depressed for too long or is covered up. Press all buttons individually. Check whether any buttons are jammed, covered up or soiled. a= Risk of electric shock! Incorrect repairs are dangerous. Repairs may only be carried out by one of our trained after-sales engineers. Replacing the bulb in the oven ceiling light If the bulb in the oven light fails, it must be replaced. Heat- resistant, 40 watt spare bulbs can be obtained from our after- sales service or a specialist retailer. Only use these bulbs. a= Risk of electric shock! Switch off the circuit breaker in the fuse box. 1. Place a tea towel in the oven when it is cold to prevent damage. 2. Unscrew the glass cover by turning it anti-clockwise. 3. Replace the bulb with one of the same type. 4. Screw the glass cover back in. 5. Remove the tea towel and switch on the circuit breaker. Glass cover You must replace a damaged glass cover. Suitable glass covers may be obtained from the after-sales service. Please specify the E number and FD number of your appliance. After- sales service Our after-sales service is there for you if your appliance needs to be repaired. We will always find the right solution in order to avoid unnecessary visits from a service technician. E number and FD number When calling us, please give the product number ( E no. ) and the production number ( FD no. ) so that we can provide you with the correct advice. The rating plate containing these numbers can be found on the right- hand side of the oven door. You can make a note of the numbers of your appliance and the telephone number of the after-sales service in the space below to save time should it be required. E no. FD no. After- sales service O Please note that there will be a fee for a visit by a service technician in the event of a malfunction, even during the warranty period. Please find the contact data of all countries in the enclosed customer service list. To book an engineer visit and product advice GB 0844 8928979 Calls from a BT landline will be charged at up to 3 pence per m...

Descargar ahora

Introduzca dos números de la imagen: