Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
Lift the panel and remove the clips from the panel (fig. C). 5. Remove the seal from the bottom of the panel (fig. D). Pull the seal and remove it up and out. Pull out the panel. 6. Pull the lower panel at an angle, upwards and out. 7. Do NOT unscrew the left and right-hand screws from the sheet metal part (fig. E). Clean the panels with glass cleaner and a soft cloth. : Risk of injury! Scratched glass in the appliance door may develop into a crack. Do not use a glass scraper, sharp or abrasive cleaning aids or detergents. Installation During installation, make sure that the lettering "top right" is upside down at the bottom left of both panels. 1. Insert the lower panel at an angle towards the back (fig. A). 2. Slide in the middle panel (fig. B). 3. Stick the retaining clips onto the right and left-hand side of the panel, aligning them so that the retaining carriers are over the screw holes, and then screw into place (fig. C). 4. Hook the seal in to the bottom of the panel again (fig. D). 5. Insert the uppermost panel at an angle to the back into the brackets. Take care not to push the seal to the back (fig. E). 6. Insert the two small seals on the left and right of the panel again (fig. F). .. .. .. .. .. .. .. .. .. .. .. .. .. 7. Put the cover back in place and screw it on. 8. Attach the oven door. Do not use the oven again until the panels have been correctly installed. Troubleshooting Malfunctions often have simple explanations. Refer to the table : Risk of electric shock! before calling the after-sales service as you may be able to Incorrect repairs are dangerous. Repairs may only be carried remedy the fault yourself. out by one of our trained after-sales engineers. Malfunction table If a dish does not turn out exactly as you wanted, refer to the Tested for you in our cooking studio section, where you will find plenty of cooking tips and tricks. Problem Possible cause Note/remedy The appliance does not work. Defective fuse Look in the fuse box and check that the circuit breaker is in working order. “Set clock” appears in the status bar. The Power cut Turn the rotary selector to set the current time then time is not the current time. “Select lan-press the 0 button. The language set remains guage” appears in the settings area on unchanged following a power failure. the right. The oven door cannot be opened. “Set Power cut during self-cleaning. Turn the rotary selector to set the current time then clock” appears in the status bar. The time press the 0 button. The language set remains displayed is not the current time. “Select unchanged following a power failure. Wait until the language” appears in the settings area on cooking compartment has cooled down. The H the right. The H symbol is displayed. symbol disappears. You can now open the oven door. The oven does not heat up or the type of Type of heating not recognised Set once again. heating selected cannot be set. The oven does not heat up. “Demo” is dis-The oven is in demo mode. Switch off the circuit breaker in the fuse box and played in the status bar. then switch back on after approx. 20 seconds. In the next 2 minutes hold the @ button down for four seconds until the text "Demo" disappears. “Automatic switch-off” appears in the sta-Automatic switch-off has been Press any button. The text disappears. You can tus bar. activated. The oven switches off. make settings again. Error messages with E to reset the time. If the error is shown again, call the after-sales service. If an error message with E is shown in the display, press the 0 button. This cancels the error message. You may then have You can take remedial action yourself if the following error messages are displayed. Error message Possible cause Note/remedy E011 A button was pressed for too long Press all buttons individually. Check that the but- or has jammed. tons are clean. If the error message remains, please contact the after-sales service. E115 The temperature in the cooking The oven door locks. Wait until the cooking comcompartment is too high. partment has cooled down. Clear the error message with the 0 button. Replacing the bulb in the oven ceiling light 3. Pull out the bulb, do not turn it (Fig. B). Insert the new bulb, making sure that the pins are in the correct position. Push the If the bulb in the oven light fails, it must be replaced. Heat- bulb in firmly. resistant, 10 watt, 12 V halogen bulbs are available from the after-sales service or specialist retailers. When handling the halogen bulb, use a dry cloth. This will increase the service life of the bulb. Only use these bulbs. : Risk of electric shock! Switch off the circuit breaker in the fuse box. 1. Place a tea towel in the oven when it is cold to prevent damage. 2. Remove the glass cover. To do this, press the metal tabs to the side with your thumb (Fig. A). $ % 4. Refit the glass cover. When doing this, insert it on one side and press firmly on the other side. The glass cover will click into place. 5. Remove the tea towel ...