Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
Rear of the recorder AUDIO INPUTVIDEO INPUT PrPbY COMPONENT VIDEO INPUT Rear of TV AVC S-VIDEO INPUT S 11 Hookup andSettings Connections to Your TV Make one of the following connections, depending on the capabilities of your existing equipment. Tips Depending on your TV and other equipment you wish to connect, there are various ways you could connect the recorder. Use only one of the connections described below. Please refer to the manuals of your TV, VCR, Stereo System or other devices as necessary to make the best connections. Caution – Make sure the recorder is connected directly to the TV. Set the TV to the correct video input. – Do not connect the recorder’s AUDIO OUT jack to the phono in jack (record deck) of your audio system. – Do not connect your recorder via your VCR. The DVD image could be distorted by the copy protection system. Video connection Connect the VIDEO OUT jack on the recorder to the video in jack on the TV using the video cable (V). Audio (Left/Right) Connection Connect the left and right AUDIO OUT jacks of the recorder to the audio left and right IN jacks on the TV using the audio cables (A). Do not connect the recorder’s AUDIO OUT jack to the phono in jack (record deck) of your audio system. S-Video connection Connect the S-VIDEO OUT jack on the recorder to the S-Video in jack on the TV using the S-Video cable (S). Component Video connection Connect the COMPONENT / PROGRESSIVE SCAN VIDEO OUT jacks on the recorder to the corresponding input jacks on the TV using an Y Pb Pr cable (C). If your television is a high-definition or “digital ready” television, you may take advantage of the recorder’s progressive scan output for the highest video resolution possible. If your TV does not accept the Progressive Scan format, the picture will appear scrambled if you try Progressive Scan on the recorder. Set the [Progressive Scan] option to [ON] on the setup menu for progressive signal, see page 16. Note: Progressive scan does not work with the analog video connections (yellow VIDEO OUT jack) or S-VIDEO connection. Caution Once the setting for Progressive Scan output is entered, an image will only be visible on a Progressive Scan compatible TV or monitor. If you set Progressive Scan to [ON] in error, you must reset the recorder. First, remove the disc in the recorder. Next, press STOP (x) and hold it for five seconds before releasing it. The video output will be restored to the standard setting, and a picture will once again be visible on a conventional analog TV or monitor. Rear of the recorder AUDIO INPUTVIDEO INPUT PrPbY COMPONENT VIDEO INPUT Rear of TV AVC S-VIDEO INPUT S Connecting to an Amplifier Connecting to an amplifier equipped with two channel analog stereo or Dolby Pro Logic ll/ Pro Logic Connect the Left and Right AUDIO OUT jacks on the recorder to the audio left and right in jacks on your amplifier, receiver, or stereo system, using the audio cables (A). Connecting to an amplifier equipped with two channel digital stereo (PCM) or to an Audio/ Video receiver equipped with a multi-channel decoder (Dolby Digital™, MPEG 2, or DTS) 1. Connect one of the recorder’s DIGITAL AUDIO OUT jacks (OPTICAL O or COAXIAL X) to the corresponding in jack on your amplifier. Use an optional digital (optical O or coaxial X) audio cable. 2. You will need to activate the recorder’s digital output. (See “Audio Settings” on page 17). Digital Multi-channel sound A digital multi-channel connection provides the best sound quality. For this you need a multi-channel Audio/Video receiver that supports one or more of the audio formats supported by your recorder (MPEG 2, Dolby Digital and DTS). Check the receiver manual and the logos on the front of the receiver. Caution: Due to the DTS Licensing agreement, the digital output will be in DTS digital out when DTS audio stream is selected. Notes: – If the audio format of the digital output does not match the capabilities of your receiver, the receiver will produce a strong, distorted sound or no sound at all. – Six Channel Digital Surround Sound via digital connection can only be obtained if your receiver is equipped with a Digital Multi-channel decoder. –To see the audio format of the current DVD in the on-screen display, press AUDIO. – This recorder does not perform internal (2 channel) decoding of a DTS sound track. To enjoy DTS multi channel surround, you must connect this recorder to a DTS compatible receiver via one of this recorder’s digital audio outputs. Rear of the recorder AUDIO INPUT DIGITAL INPUT COAXIAL DIGITAL INPUT OPTICAL Amplifier (Receiver) A X O Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic”, and the double- D symbol are trademarks of Dolby Laboratories. “DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc. 12 13 Hookup andSettings Accessory Audio/Video (A/V) Connections Connecting to the AV IN 1 or AV IN 2 Jacks Connect the input jacks (AV IN 1, AV IN 2) on the recorder to the audio/video out jacks o...