Votos - 4, Puntuación media: 4.3
(
)
)
|
Resumen del manual
This recorder is only compatible with DV-format (DVC-SD, DV25) camcorders. Digital satellite tuners and Digital VHS video recorders are not compatible. You cannot connect more than one DV camcorder at a time to this recorder. You cannot control this recorder from external equipment connected via the DV IN jack (including two recorders). It may not always be possible to control the connected camcorder via the DV IN jack. Digital camcorders can usually record audio as stereo 16-bit/48kHz, or twin stereo tracks of 12- bit/32kHz. This recorder can only record one stereo audio track. Set [DV Rec Audio] option to [Audio 1] or [Audio 2] as required (see page 22). Audio input to the DV IN jack should be 32 or 48kHz (not 44.1kHz). Picture disturbance on the recording may occur if the source component pauses playback or plays an unrecorded section of tape, or if the power fails in the source component, or the DV cable becomes disconnected. Recording from a Digital Camcorder You can record from a digital camcorder connected to the DV IN jack on the front panel of this recorder. Using the recorder’s remote, you can control both the camcorder and this recorder. Before recording, make sure that the audio input for the DV IN jack is set up (see page 22). Tips: The source signal must be DVC-SD format. Some camcorders cannot be controlled using this recorder’s remote. If you connect a second recorder using a DV cable, you cannot control the second DVD from this one. You cannot control this unit remotely from a component connected to the DV IN jack. You cannot record date and time information from a DV cassette. 1. Make sure your digital camcorder is connected to the front panel DV IN jack. See page 14. 2. Select [TV(HDD)] or [TV(DVD] option on the HOME menu then press ENTER. (see page 15). 3. Check that the DV audio input is as you require. You can choose between Audio 1 (original audio) and Audio 2 (overdubbed audio). DV Input is set from the [DV Rec Audio] in sub-menu of the Setup menu. See “DV Recording Audio” on page 22 for more information. 4. Press AV repeatedly to select the DV input. DV appears in the display window and on the TV screen. 5. Find the place on the camcorder tape that you want to the recording to start from. For best results, pause playback at the point from which you want to record. Depending on your camcorder, you can use this recorder’s remote to control the camcorder using the STOP, PLAY and PAUSE functions. 6. Press REC (z) once to start recording. Recording is automatically stopped if the recorder detects no signal. You can pause or stop the recording by pressing PAUSE/STEP (X) or STOP (x). You cannot control the camcorder from this remote control during recording. In Video mode, the final frame of the recording may remain displayed on screen for a while after recording stops. For timer recording to work properly on this recorder, the digital camcorder must also be switched on and in operating. Troubleshooting If you cannot get a picture and/or audio through the DV IN jack, check the bullet points: Make sure the DV cable is properly connected. Try switching off the connected equipment then switch back on. Try switching the audio input. Note: Depending on the connected camcorder, you may not be able to control it using the remote control supplied with this recorder. Title List and Chapter List Menu Overview Using the Title List menu you can edit video content. The editing features available in the Title List menu depend on whether you are editing video on DVD, or the HDD, and whether you’re editing Original content, or a Playlist. There are two ways to edit VR mode DVD-RW discs. You can directly edit the Original content of the disc, or you can create and edit a Playlist. The Playlist doesn’t actually change any of the content on the disc, but just controls how the content is played back. Editing material recorded on the HDD is similar to editing the Original content of a VR mode DVD-RW, with similar commands for erasing and naming titles, as well as fine control over the content of chapters within titles for DVD disc. Note: During recording, if you display the Title List menu for the HDD, some of the titles may appear with a mark. These titles were recorded with a Line Input setting different to the current setting of the recorder. During recording, these titles cannot be played. 1. Press MENU/LIST to display the Title List menu. Playback should be stopped when you do this. • You can also access it using HOME menu, select [TITLE LIST] option then press ENTER. • When selecting titles, use the v / V buttons to display the previous/next page if there are more than six titles. • If you are editing a VR mode disc, press MENU/LIST to switch between Original and Playlist menu. On the left side of the screen are the menu options. The main part of the screen shows thumbnails of the titles (or chapter) on the DVD or HDD. You can change these thumbnails using the THUMBNAIL button—see Changing Title Thumbnai...