Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
If the LCD panel or video monitor is used for televisionreception, video or DVD play, the LCD panel or video monitor must beinstalled so that these features will only function when the vehicle is in“park” or when the vehicle’s parking brake is applied. An LCD panel or video monitor used for television reception, video orDVD play that operates when the vehicle is in gear or when the parkingbrake is not applied must be installed to the rear of the driver’s seatwhere it will not be visible, directly or indirectly, to the operator of themotor vehicle. Important Note This DVD player incorporates two new features: 1) A wireless FM Modulator 2) Capability to add an optional plug in TV tuner ( P/N PODTVT – must be ordered separately) Please be advised that the wireless modulator will perform well inmost applications. However, in certain applications the quality ofthe wireless signal may be less than optimal, resulting in static orstrong local station bleed thru. If this is the case, an optional relaybox is available. The part number is SIRSWB and plugs into the 1/ 8" jack on the side of the chassis. This relay box is installed between the vehicle antenna and the car radio to provide the bestpossible FM reception of the DVD player audio. When the SIRSWB is installed it is recommended that the wireless FM antenna that is plugged into the printed circuit board next to the3.5mm jack be unplugged. See page 6 of this manual for additional information. GENERAL INSTALLATION APPROACH: 1) Decide upon system configuration and options that will be installed (i.e.: what components, VCP, Video Game, external amp, wireless headphones, VCP, etc.). 2) Review all manuals to become familiar with electrical requirements and hook ups. 3) Decide upon mounting locations of all components and method of mounting. 4) Prep the vehicle by removing any interior trim necessary to gain access to vehicle's wiring as well as all areas where interconnecting wire harnesses will need to be located. If any access holes need to be cut into the vehicle (headliner, other trim components etc.), this should be done now as well. (Refer to Page 3). 5) Route the wiring harnesses throughout the vehicle as necessary. (Refer to the Wiring Diagrams on pages 6 of this manual as well as the wiring instructions for the individual components and accessory options being installed). Be sure that all wiring is protected from sharp edges and is routed in such a manner that it will not be pinched when all components and interior trim are fully installed. Be sure to leave enough slack in the wiring at each component to allow working room. 6) Remove all A/V system components from their packaging and place them loosely in the vehicle at their respective locations. 7) Connect all components together (electrically) and verify proper operation of all system functions. Note: This is best done BEFORE, components have been permanently mounted. 8) After verifying proper operation of the system, proceed to mount of each component. 9) When all components are mounted, recheck function of entire system again to ensure that no wiring was pinched or connected improperly during final installation. GENERAL SYSTEM CONFIGURATIONS: The following is intended to provide some of the system configurations that are possible with the JN102 series Drop Down Video Systems: Notes : There are a few audio output options that can be added as follows: a) Wireless Headphones (P/N MVIRHS). b) Wired relay box for wireless FM Modulator (P/N SIRSWB). The JN102 video systems are only intended for an overhead, drop down installation. It is not intended for Seatback or any other type of mounting. The hinging mechanism is designed for horizontal, drop down use only. -2 VEHICLE PREPARATION: 1) Locate an accessory power source (+12v when key is in the ACC. and run positions, and 0v when key is off), and also a good ground generally, these wires can be found at the ignition switch or fuse-box. 2) The mounting method and location will vary from vehicle to vehicle, so this manual will only focus on the installation of the video monitor and related console accessories. 3) Generally, the best location for the video monitor is where the vehicle's factory dome light is installed. The monitor should be located in such a manner that it can be comfortably viewed by rear seat passengers. NEVER INSTALL THE MONITOR IN A PLACE WITHIN THE DRIVER'S VIEW. THIS IS NOT ONLY DANGEROUS, BUT IT IS ALSO ILLEGAL IN MANY STATES. 4) Once the mounting location of the monitor has been determined, there may be additional preparation work necessary, depending on the vehicle structure and installation method. Some of the steps that may be required are: A) Removal of the vehicle's dome light B) The headliner may. C) If the mini-console will be used, it will have to be trimmed to fit the contour of the vehicle's headliner. Refer to the "Mini-Console installation" section in this manual. -3 MINI CONSOLE INSTALLATION: This page only covers special in...