Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
Symptom Cause Possible Solution(s) No power. • The power cord is disconnected. • Plug the power cord securely into the wall power outlet. The power is on, but the DVD/CD player does not work. • No disc is inserted. • Insert a disc. (Check that the DVD or, audio CD indicator in the DVD display is lit.) No picture. • The TV is not set to receive DVD signal output. • Select the appropriate video input mode on the TV so the picture from the DVD/ CD receiver appears on the TV screen. • The video cable is not connected securely. • Connect the video cable into the jacks securely. • The connected TV power is turned off. •Turn on the TV. There is no sound or only a very low-level sound is heard. • The equipment connected with the audio cable is not set to receive DVD signal output. • Select the correct input mode of the audio receiver so you can hear the sound from the DVD/CD player. • The audio cables are not connected securely. • Inseart the audio cables into the jacks securely. • The power of the equipment connected with the audio cable is turned off. •Turn on the equipment connected with the audio cable. • The audio connecting cable is damaged. • Replace it with new one. The playback picture is poor. • The disc is dirty. • Clean the disc. The DVD/CD player does not start playback. • No disc is inserted. • Insert a disc. (Check that the DVD, or audio CD indicator in the DVD display is lit.) • An unplayable disc is inserted. • Insert a playable disc. (Check the disc type, color system and Regional code.) • The disc is placed upside down. • Place the disc with the playback side down. • The disc is not placed within the guide. • Place the disc on the disc tray correctly inside the guide. • The disc is dirty. • Clean the disc. •A menu is on the TV screen. • Press the SETUP button to remove the menu display. •A parental control restriction is set. • Cancel the estriction or change the rating level. Loud hum or noise is heard. • The plugs and jacks are dirty. •Wipe them with a cloth slightly moistened with alcohol. • The disc is dirty. • Clean the disc. • The speakers and components are connected poorly. • Connect the speakers and components securely. • The DVD/CD player is located too close to the TV. • Move your TV away from the audio components. 32 REFERENCE Troubleshooting (Cont’d) Symptom Radio stations cannot be tuned in. The remote control does not work properly. The sound mode or Pro Logic II mode cannot be changed. The front panel display is too dim. Cause • The antenna is positioned or connected poorly. • The signal strength of the stations is too weak (when tuning in with automatic tuning). • No stations have been preset or preset stations have been cleared (when tuning by scanning preset stations). • The remote control is not pointed at the remote sensor of the DVD/CD player. • The remote control is too far from the DVD/CD player. • There is an obstacle in the path of the remote control and the DVD/CD receiver. • The batteries in the remote control are exhausted. • The system cannot change while play- ing MP3 or WMA discs. • Nothing is displayed on the front panel display. Possible Solution(s) • Connect the antenna securely. • Adjust the antennas and connect an external antenna if necessary. •Tune in the station manually. • Preset the stations (page 28). • Point the remote control at the remote sensor of the DVD/CD player. • Use the remote control within about 23 ft (7 m). • Remove the obstacle. • Replace the batteries with new ones. • Eject disc, change mode, reinsert disc. • Press DIMMER on the remote control. Troubleshooting (Cont’d) Symptom Radio stations cannot be tuned in. The remote control does not work properly. The sound mode or Pro Logic II mode cannot be changed. The front panel display is too dim. Cause • The antenna is positioned or connected poorly. • The signal strength of the stations is too weak (when tuning in with automatic tuning). • No stations have been preset or preset stations have been cleared (when tuning by scanning preset stations). • The remote control is not pointed at the remote sensor of the DVD/CD player. • The remote control is too far from the DVD/CD player. • There is an obstacle in the path of the remote control and the DVD/CD receiver. • The batteries in the remote control are exhausted. • The system cannot change while play- ing MP3 or WMA discs. • Nothing is displayed on the front panel display. Possible Solution(s) • Connect the antenna securely. • Adjust the antennas and connect an external antenna if necessary. •Tune in the station manually. • Preset the stations (page 28). • Point the remote control at the remote sensor of the DVD/CD player. • Use the remote control within about 23 ft (7 m). • Remove the obstacle. • Replace the batteries with new ones. • Eject disc, change mode, reinsert disc. • Press DIMMER on the remote control. 33 Specification Specification [General] Power supply Refer to main label Power consumption Refer to main label Mass 8.4 lbs External ...