Votos - 3, Puntuación media: 3.3
(
)
)
|
Resumen del manual
Before you begin: . Place the System in VCR mode. Press VCR so the red VCR light appears on the front of the System. Select a recording speed (SP, SLP) with the MODE/SPEED button. . Put a videotape in the cassette compartment. Make sure the tape’s record tab is intact and the tape is long enough to record the 1 program(s). 1 1 Press SKIP i /CH o or SKIP j /CH p or the Number buttons to select the channel you want to record. 2 2 Press RECORD I on the front of the System until the desired recording length (30 minutes to eight hours) appears on the TV screen. Recording will begin.The RECORD light and the TIMER REC light will appear on the front of the System. OT. (0:30. S. Stopping an OTR To stop an OTR before recording is finished, press STOP C on the remote control or STOP/EJECT C A on the front of the System. To cancel the OTR but continue recording, press RECORD I on the front of the System repeatedly until REC appears in the upper left corner of the TV screen. When an OTR finishes, the System will switch to DVD mode and/or turn itself off.The TIMER REC light will flash because the VCR of the System is still on standby for timer recordings. Press TIMER SET on the remote or STOP/EJECT C A on the System to cancel timer standby and use the VCR of the System normally again. • The remaining recording time will appear on the display panel. Press DISPLAY to see it on the TV screen. • To change the recording length while an OTR is in progress, press RECORD I on the front of the System. • You cannot start a timed OTR with the REC I button on the remote. • You cannot pause an OTR. • If the end of the tape is reached during an OTR, the VCR will stop recording, eject the tape, and switch to DVD mode and/or turn off. The TIMER REC light will flash. Press TIMER SET on the remote or STOP/EJECT CA on the System to cancel timer standby and use the VCR again. • If you press TIMER SET for a Timer Recording, the OTR will stop immediately.The System will switch to DVD mode or turn off for the recording. Helpful Hints 2Press RECORD I on the front of the System. STANDBY-ON TIMER SET VCR/TV SEARCH MODE REPEAT TUNER 3 4 5 6 7 8 9 SLOW 0+10 21 VCRDVD CLEAR DISPLAY SETUP/ PROG TITLE RETURNMODE/SPEED C-RESET AUDIO/ BAND ANGLESUBTITLE ZOOM DISC MENU OK PAUSE REW FF PLAYSTOP SKIP/ CH SKIP/ CH REPEAT SOUNDSURROUND +– VOLUME REC A-B E9000(P01-54).QX33.latest 03.6.5 2:51 AM Page 37 E9000(P01-54).QX33.latest 03.6.5 2:51 AM Page 37 Rerecording (Tape Duplication) 37 These instructions show you how to copy videotapes.The illustration uses two MRD500 Systems. Other VCRs or Camcorders may operate differently. 1. Audio cables from red/white AUDIO (DVD/VCR OUT) jacks of System 1 to AUDIO (VCR IN) jacks of System 2 2. Video cable from yellow VIDEO (DVD/VCR OUT) jack of System 1 to yellow VIDEO (VCR IN) jack of System 2 PROGRESSIVE OUT IN ) P I PROGRESSIVE OUT IN ) P I System 1 (Plays tape) System 2 (Records tape) 3. RF coaxial cable from the TV ANTENNA OUT jack of System 2 to the TV’s ANTENNA IN Jack 1 1 Make the connections shown above. 2 2 System 1 will play your tape. Put a prerecorded tape into the cassette compartment of System 1. Press VCR to put the unit in VCR mode if necessary. 3 3 System 2 will record your tape. Insert a blank tape in the cassette compartment of System 2. Press VCR to put the unit in VCR mode if necessary. 4 4 Turn on the TV and set it to channel 03 (the RF output channel of System 2). (To change the System’s output channel, see step 6 on page eight.) 5 5 Point the remote control at System 2. Press Number buttons 0, 0, 1 or 0, 0, 2. (See Helpful Hints at right.) 6 6 Press MODE/SPEED to select SP or SLP at System 2. 7 7 Press PLAY B (VCR) on the front of System 1 and RECORD I on the front of System 2 at the same time. To stop recording, press STOP/EJECT CA on System 1, then press STOP/EJECT CA on System 2. Helpful Hints • If you use the AUDIO and VIDEO (VCR IN) jacks on the back of System 2, press Number buttons 0, 0, 1 at step 5. L1 will appear on the TV screen and the System’s display panel. • If you use the AUDIO and VIDEO In jacks on the front of System 2, press Number buttons 0, 0, 2 at step 5. L2 will appear on the TV screen and the System’s display panel. • Unauthorized recording of copyrighted television programs, videotapes, or other materials may infringe on the rights of copyright owners and violate copyright laws. • If a program has copyright protection, it may not record clearly. E9000(P01-54).QX33.latest 03.6.5 2:51 AM Page 38 E9000(P01-54).QX33.latest 03.6.5 2:51 AM Page 38 38 Timer Recording Follow these steps to program the System’s VCR to record TV programs while you’re away. Before you begin: . Set up the TV channels at the System. Details are on page 28. . Set the clock. Details are on pages 30-31. . Put a tape in the cassette compartment. Make sure the tape’s record tab is intact and the tape is long enough to record the program(s). If the end of the tape is reached during a Timer Recording,recording...