Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
This function should only be used if directly by Microboards Technical Support. Update Firmware The Update Firmware feature is used to update the controller firmware. 1. To update the firmware: Place the firmware CD into the TOP reader drive. 2. Press the ENT button 3. The display will show: Update F/W X.12Y To M.45R YES? 4. Press the ENT button to complete the firmware update. 5. The duplicator will reboot automatically after installing the new firmware. Compare Firmware The Compare Firmware function is used to compare the firmware installed on the controller with the firmware on the CD. H/W Diagnostic Hardware Diagnostics runs a number of tests on the controller. Normally this function is used by service personnel. Load Default The Load Default feature will set all the values back to the factory default settings. 16 CD+G The CD+G feature, when set to ON in the Advanced Setup Menu, will allow you to copy a CD+G Karaoke master disc. The default setting is OFF. Important Note: The CD+G value must be set to OFF to use the Track Extraction feature. To enable CD+G duplication, perform the following steps: 1. Press and HOLD the ESC button for 3 seconds to enter the Advanced Setup Menu 2. Press the UP or DOWN arrows until the display reads 10-9: Adv Setup CD+G 3. Press ENT to adjust the CD+G setting 4. Use the UP or DOWN arrows to alternate the setting between ON and OFF 5. Press ENT when ON is displayed to enable CD+G duplication 6. Press ESC to exit the Advanced Setup Menu 7. Use the UP or DOWN arrow to return to Copy mode ISRC & MCN The ISRC (International Standard Recording Code) & MCN (Media Catalog Number) feature allows you to copy this information from a CD audio master to the blank disc. The default setting is OFF. USB Option This function is not used in the QD-MultiDrive Series. CD Text This feature allows CD-Text content to be copied from master to blank. The default is OFF. Disc Counter This feature allows you to view the number of successful and unsuccessful burns. The JC OK entry is for successful burns for the entire unit; you can also view the individual drive performance by using the Ў^ buttons. Update Drive F/W This feature is not used by the QD- MultiDrive. 17 Specifications – QD-MultiDrive Series Model Recorders Dimensions, inches (H x W x D) Weight, lbs QD-123 3 10.5 x 8 x 17 21 lbs QD-125 5 17 x 8 x 18 33 lbs QD-127 7 17 x 8 x 18 37 lbs • Product Interface ATAPI/ IDE • Firmware Upgrade Via CD-ROM • Read Speed 52X • AC Input: 115/230 VAC; 8/5 AMPS • Write Speed 52X MAX; 50-60Hz • System Display LED • Maximum Operating Temperature: 25 • Write Method Auto Detect (DAO, TAO ) Degrees C. • Operation Mode COPY, TEST, SCAN, • Relative Humidity: 30% - 80% non- SAFE condensing • Data Buffer 1 MB Supported Formats CD-ROM Mode 1 & 2 CD-DA , CD-ROM/XA Video CD , Game CD Mix Mode, Multisession , HFS CD Bridge , Photo CD , CD Extra, CD+G (Karaoke) • Recommended Media: Taiyo Yuden CAUTION: Disconnect AC Power Cord Before Servicing. High Voltages Present with Unit Powered Off and Line Cord Connected. Technical Support For technical questions or support issues, contact Microboards Technology technical support: United States Europe Japan PH: 952-556-1639 PH: +44 (0) 845 230 7800 PH: 03-3561-2266 FAX: 952-556-1628 support@microboards.com Please have the Model and Serial Number of your QD available when contacting Technical Support. Any unauthorized modification to this equipment may result in the revocation by the FCC of the user’s authority to operate this equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the equipment and antenna • Connect the equipment into an outlet on a circuit different than that to which the receiver is connected • Consult the dealer or an experienced radio/TV technician for help This product is in conformity with the EMC Directive (89/336/EEC) through compliance with the following European standards: EN 55022, EN 55024. The CE mark has been affixed in accordance with the CE Marking Directive 93/68/EEC. Canadian Department of Communications (DOC) Statement This Class B digital apparatus complies with the Ca...
Otros modelos de este manual:lector de DVD - QD-125 (248.19 kb)
lector de DVD - QD-MultiDrive (248.19 kb)
lector de DVD - QD-123 (248.19 kb)