Votos - 4, Puntuación media: 4.3
(
)
)
|
Resumen del manual
. O CD-R O . O CD-RW (O) O O DVD DVD-Stamp . . O DVD-R 4.7GB (FOR GENERAL Ver 2.0) O . O 4.7GB (FOR AUTHORING : Disc-at Once mode) . . O 3.95GB (FOR AUTHORING : Disc-at Once mode) . . O DVD-RW 4.7GB(For General Ver 1.0) . . O 4.7GB(For General Ver 1.1) (O) O O DVD+R 4.7GB (Basic Ver 1.0) O x O DVD+RW 4.7GB (Basic Ver 1.1) (O) O O Writable : write once, read many times. Rewritable : write data one or more times. Buffer underrun prevention technology Buffer underrun prevention technology This technology eliminates Buffer underrun Error Recommended Disc Types CD-R Media (16x/8x/4x) Mitsubishi, Taiyo-Yuden, Mitsui, Ricoh, Fujifilm, Sony, Hitachi Maxell, Memorex, RITEK, CMC, P.V.C, JVC, SKC, ACER, Prime Disc, TDK CD-RW Media (10x/4x) Ricoh, Mitsubishi, ACER, OPTROM, Memorex, P.V.C, RITEK, CMC, LEADDATA, GigaStorage, Prodisc, Fornex, Sumsung, Philips DVD-R Media (4x/2x, 4.7GB For General DISC) Mitsubishi, Taiyo-Yuden, Panasonic, Hitachi Maxell, TDK, PVC, Fuji Film, Ritek, Verbatim DVD-RW Media (2x/1x) JVC, Pioneer, Mitsubishi, TDK, Verbatim DVD+R Media (4x/2.4x) RICOH, Mitsubishi, TDK, Verbatim, Taiyo-Yuden, Sony, Hitachi Maxell DVD+RW Media (2.4x) RICHO, Mitsubishi, TDK, Verbatim Reading / Recording Speed Reading Speed(MAX) DVD-ROM (12x), CD-ROM (40x), DVD-R (5x), DVD-RW (5x), DVD+R (5x), DVD+RW (5x) CD-R (40x), CD-RW (32x) Recording Speed(MAX) DVD-R (4x), DVD-RW (2x), DVD+R (4x), DVD+RW (2.4x),CD-R (16x), CD-RW (10x) Features Ultra Speed CD-RW DISC(24X higher) does not support Reading / Recording. We recommend using the 'Recommended Disc Types'. When you use the other disc, may affect Reading / Recording of the data. Installing Drive 1. Turn the PC off. 2. Open the cover as shown in the picture. 3. If necessary, attach the support devices on both sides of the drive - The support devices are PC accessories. Purchase a pair if necessary. 4. Insert the DVD±R/RW Drive after removing the plate as below - If you cannot remove/insert the plate smoothly, use the floppy disc slot instead. Connecting Cables Connecting the Power Cable Hold the power cable (with four pins) in the power box within the computer with the cutoff edges( ) facing up and connect it to the power port in the back of the DVD±R/RW Drive A -Cutoff edges 1 +5V DC 2 Ground 3 Ground 4 +12V DC Improperly connected power cable may cause malfunction. Check the direction of the power cable and the cutoff edges before connecting the cable. Connecting E-IDE Cable We recommend that you use the 80-pin E-IDE cable that comes with the purchase of the drive for stable performance. When you use one E-IDE cable Connect the cable to SL (slave) in the Master/Slave port in the back of the DVD±R/RW Drive. a : Slave Drive (Select the SL jumper) b : HDD c : MotherBoard When you use two E-IDE cables Connect the cable to MA in the Master/Slave port in the back of the DVD±R/RW Drive. When you have one DVD±R/RW Drive: Set it to MA (Master) a : Master Drive (Select the MA jumper) b : HDD c : Motherboard d : Primary 1 e : Secondly 1 When you have one DVD±R/RW Drive and the other ODD products: Set it to MA (Master) / SL (Slave), a : Master Drive (Select the MA jumper) b : Slave Drive (Select the SL jumper) c : HDD d : Motherboard e : Primary 1 f : Secondly 1 c : HDD d : Motherboard e : Primary 1 f : Secondly 1 Connecting the Jumper to the Master/Slave Port Connect the jumper to the slot in the back of the DVD±R/RW Drive. When you connect the jumper to MA (Master), the drive runs as the master, and when you connect it to SL (Slave), the drive runs as the slave. When you connect it to CS (CSEL), you can control the device using the host interface signal CSEL. (Connection to MA is recommended.) MA : Master SL CS : Slave : Cable Select(CSEL) Connecting the Audio Cable (When Connected to the Sound Card) Connect the Sound Output Port in the back of the DVD±R/RW Drive to the audio input port of the sound card using the audio cable to hear the sound from the drive. Software Setup 1. Insert the CD provided with the DVD±R/RW Drive to install the device program. The program runs automatically. If the automatic start fails, find the setup.exe file in the CD-ROM drive folder using Windows Explorer and double-click it. 2. Click [Install All Softwares Driver ] Once the installation process begins, follow the instructions. 3. Check [Yes, I want to restart my computer now] and click [Finish]. Use the DVD±R/RW Drive after rebooting the system. Uninstall any previously installed recording software before installing new recording software provided by SEC. You may experience compatibility problems running your new software if you install the new SEC software with other recording software programs remaining on the system. Fimware Upgrade 1. Go to 2. Click Firmware on the menu bar (in the upper right-hand corner). Confiming Confirming Using [Device Manager] Windows 98/Me 1. Click [Start] - [Settings] - [Control Panel] - [System] 2. Click on the [Device Manager] tab in the System ...