Votos - 1, Puntuación media: 3
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
By connecting the unit to a broadband home network, you have access to services such as software updates, BD-LIVE interactivity and on-line content services. Wired network connection Using a wired network provides the best performance, because the attached devices connect directly to the network and are not subject to radio frequency interference. Please refer to the documentation for your network device for further instructions. Connect the player’s LAN port to the corresponding port on your Modem or Router using a commercially available LAN or Ethernet cable. yyWhen plugging or unplugging the LAN cable, hold the plug portion of the cable. When unplugging, do not pull on the LAN cable but unplug while pressing down on the lock. yyDo not connect a modular phone cable to the LAN port. yySince there are various connection configurations, please follow the specifications of your telecommunication carrier or internet service provider. yyIf you want to access content from DLNA servers, this player must be connected to the same local area network with them via a router. yyTo set your PC as a DLNA server, install the supplied Nero MediaHome 4 on your PC. (see page 67) ,,Note Rear of the unitRouterBroadband serviceDLNA certified servers Wired Network Setup If there is a DHCP server on the local area network (LAN) via wired connection, this player will automatically be allocated an IP address. After making the physical connection, a small number of home networks may require the player’s network setting to be adjusted. Adjust the [NETWORK] setting as follow. PreparationBefore setting the wired network, you need to connect the broadband internet to your home network. 1. Select [Connection Setting] option in the [Setup] menu then press ENTER (b). 2. Read the preparations for the network settings and then press ENTER (b) while [Start] is highlighted. Network will automatically be connected to the unit. Advanced Setting If you want to set the network settings manually, use W/S to select [Advanced Setting] on the [Network Setting] menu and press ENTER (b). 1. Use W/S to select [Wired] and press ENTER (b). 2. Use W/S/A/D to select the IP mode between [Dynamic] and [Static]. Normally, select [Dynamic] to allocate an IP address automatically. If there is no DHCP server on the network and you want to set the IP address manually, select [Static] then set [IP Address], [Subnet Mask], [Gateway] and [DNS Server] using W/S/A/D and numerical buttons. If you make a mistake while entering a number, press CLEAR to clear the highlighted part. ,,Note 3. Select [Next] and press ENTER (b) to apply network settings. Network connection status is displayed on the screen. 4. Press ENTER (b) while [Close] is highlighted to finish the wired network settings. Wireless Network Connection Another connection option is to use an Access Point or a wireless router. The network configuration and connection method may vary depending on the equipment in use and the network environment. Wireless CommunicationDLNA certified serversAccess Point or Wireless RouterBroadband service Refer to the setup instructions supplied with your access point or wireless router for detailed connection steps and network settings. For best performance, a direct wired connection from this player to your home network’s router or cable/DSL modem is always the best option. If you do chose to use the wireless option, note that performance can sometimes be affected by other electronic devices in the home. Wireless Network Setup For the wireless network connection, the player needs to be set up for network communication. This adjustment can be done from the [Setup] menu. Adjust the [NETWORK] setting as follow. Setting up the access point or the wireless router is required before connecting the player to the network. PreparationBefore setting the wireless network, you need to: --connect the broadband internet to the wireless home network. --set the access point or wireless router. --note the SSID and security code of the network. 1. Select [Connection Setting] option in the [Setup] menu then press ENTER (b). 2. Read the preparations for the network settings and then press ENTER (b) while [Start] is highlighted. If wired network is not connected to the unit, all available networks are displayed on the screen. 3. Use W/S to select a desired SSID of wireless network and press ENTER (b). If you have security on your access point, you need to input the security code as necessary. yyWEP security mode generally have 4 keys available on an access point setting. If your access point or wireless router use WEP security, enter the security code of the key “No.1” to connect on your home network. yyAn Access Point is a device that allows you to connect to your home network wirelessly. ,,Note 4. Use W/S/A/D to select the IP mode between [Dynamic] and [Static]. Normally, select [Dynamic] to allocate an IP address automatically. If there is no DHCP server on the network and you want to set the IP ad...