Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
• Do not let unconnected wires or terminals touch metal on the car or anything else conducting electricity. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals. • After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly. • Insulate unconnected wires with vinyl tape or other similar material. English-3 Installation Installation Accessories A.........2 D.........1B(M5X8mm).........4 C(o5X20mm).........4 E.........1 H.........1F.........1 G.........1 I.........1 ¦ Installation for Navigation System O4 A B (M5x8mm) C (O5x20mm) Holes for attachment Holes for suspension and attachment 2CAUTION • Select for installation a location where the unit can be placed completely horizontal. • Be sure to firmly stabilise this product. Do not install it in a location which is not stable. 2WARNING Check that there are no wiring cables or other parts beneath the floor mat before cutting the floor mat. 4-English ¦ ¦ 2CAUTION • GPS antenna D can be installed either inside or outside of the car, but either way it should be installed as horizontally as possible to allow easy reception of the GPS satellite signals. • The reception conditions of the GPS satellite will be less favorable with installation inside the car as compared to outside the car. Depending on the type of car, reception of the GPS satellite signals might not be possible with an inside installation. Installation outside of the car is recommended if circumstances allow. • The GPS antenna should be installed at a position that is spaced at least 12 inch (30 cm) from cellular phone or other transmitting antennas. Signals from the GPS satellite may be interfered with by these types of communication. • Do not remove the tape from the back of the GPS antenna. When the tape comes off, the waterproof effectiveness is diminished and this may cause a fault in the GPS antenna. • Painting the GPS antenna with (metallic) paint may cause a drop in performance. . Installation Outside the Car Installation to the trunk lid is made with the GPS antenna D built-in magnet. 1 Affix the waterproof pad that accompanies E at the place that comes up against the waterproof rubber lining the trunk. 2 Draw the cable of D from the trunk lid into the trunk. D E . Installation Inside the Car Install at a place close to the window surface at the center of the rear tray or on the inside of the rear window to allow easy reception of the GPS satellite signals. 1 Peel off the release paper of F and affix to placement position of D. 2 Place D on F. D F English-5 Connection PRK SW S SENS Wiring harness G Parking sensor wire (Green) To parking brake detection switch harness of car Car speed signal intermediate wire H (White) To the car speed signal harness For the sake of safety, be sure to connect the parking sensor wire. 2WARNING Car speed signal wire (White) D Remote Control Sensor accompanying the Remote Control Audio Output (MONO) (Black) Visual Output (Yellow) (3A) When disconnecting the interface cable, pinch and pull the ring of the connector. If you pull other parts of the connector, the locking mechanism of the connector is not released, which may damage the connector. 2CAUTION I/F Cable I To the monitor unit ("NAV I/F" terminal) Voice control microphone (Optional) Do not remove the cap when not connecting the cable. NOTE (5A) 2WARNING • Do not cut off the holder marked "S SENS" (containing a protection diode) of the car speed signal detection wire H (White). Doing so will cause a fault with the car. • Please contact your dealer for information about the connection S SENS method. A connection error will lead to car breakdown. 6-English Attaching Remote Control Sensor When using a TV monitor other than ones manufactured by KENWOOD, attach the Remote Control Sensor following the procedure below: Backing paper Double-sided tape 1 Remove the backing paper from the double-sided tape and attach the tape to the back of the Remote Control Sensor. 2 After wiping off the dirt or oil from the attachment location, attach the Remote Control Sensor. •Wipe off the dirt or oil from the surface to which the Sensor is attached. •Avoid locations under direct sunlight or near the TV monitor where signals from the remote controller are not received easily. NOTE Attaching Remote Control Sensor When using a TV monitor other than ones manufactured by KENWOOD, attach the Remote Control Sensor following the procedure below: Backing paper Double-sided tape 1 Remove the backing paper from the double-sided tape and attach the tape to the back of the Remote Control Sensor. 2 After wiping off the dirt or oil from the attachment location, attach the Remote Control Sensor. •Wipe off the dirt or oil from the surface to which the Sensor is attached. •Avoid locations under direct sunlight or near the TV monitor where signals from the remote controller are not received easily. NOTE REVERSE TEL mute wire (Brown) Connect t...