Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
C Connect the supplied RF cable between the VHF/UHF OUT connector on the rear panel of the unit and the TV’s antenna terminal. AV Connection 8To connect to a TV with AV input connectors — A Connect the antenna, unit and TV as per “RF Connection.” B Connect an optional audio/video cable between the AUDIO/VIDEO OUTPUT connectors on the rear panel of the unit and the TV’s audio/video input connectors. . Set your TV to AV mode. . For switching the TV’s mode, refer to the instruction manual of your television. . To obtain high-quality pictures, you can also use the Component Video Connection. (DVD deck only) (. pg. 14) D D Connect the unit to power source. Plug the end of the AC power cord into an AC outlet. This unit performs Plug & Play Set automatically. (. pg. 16) . The clock and tuner channels will automatically be set when the antenna is connected and when the AC power cord is first connected to an AC outlet. (If “AUTO” and the channel indicator are displayed on the front display panel before the unit is powered on, the clock and tuner channels are being set automatically. Wait for the time to be displayed on the front display panel before turning on the unit.) E E Set the VCR channel. The VCR channel is the channel on which you can watch the picture from the unit on the TV when only using RF connection. With RF connection, set the VCR channel to “3 CH” or “4CH.” . The VCR channel is preset to “3 CH.” Set to “4CH” if the Channel 3 is used for broadcasting in your area. With AV connection, set the VCR channel to “– CH” (off). To set the VCR channel, perform the following steps: Before performing the following steps: . Make sure there is no cassette inserted in the unit. . Make sure the unit is turned on, then press VCR/ DVD on the unit or VCR on the Remote so that the VHS indicator lights up on the front display panel. A Press POWER to turn off the unit, then press 8 STOP on the unit for more than 5 seconds. “3 CH” appears on the front display panel. B Press CH +/– on the Remote to select “3 CH,” “4CH” or “– CH” (off), then press ENTER. 14 EN INSTALLING YOUR NEW UNIT (cont.) Component Video Connection (DVD deck only) ATTENTION Be sure to connect the unit’s VIDEO OUTPUT (DVD/ VCR) connector to the TV’s VIDEO input connector. Antenna or Cable To Component Video Input connector Component Video cable (not supplied) Audio/Video cable (not supplied) AC outlet AC power cord Back of unit RF cable (supplied) COMPONENT VIDEO OUT Matching transformer (not supplied) Coaxial cable Flat feeder VIDEO OUTPUT AUDIO OUTPUT VHF/UHF OUT VHF/UHF IN To 75 ohm Terminal TV 8To connect to a TV with component video input connectors . . . A A Connect the unit to TV. A Connect the antenna, unit and TV as per “AV Connection.” (. pg. 13) B Connect the unit’s COMPONENT VIDEO OUT connectors to the TV’s component video input connectors. B B Connect the unit to power source. Plug the end of the AC power cord into an AC outlet. This unit performs Plug & Play Set automatically. (. pg. 16) . The clock and tuner channels will automatically be set when the antenna is connected and when the AC power cord is first connected to an AC outlet. (If “AUTO” and the channel indicator are displayed on the front display panel before the unit is powered on, the clock and tuner channels are being set automatically. Wait for the time to be displayed on the front display panel before turning on the unit.) C C Set the VCR channel to off. Before performing the following steps: . Make sure there is no cassette inserted in the unit. . Make sure the unit is turned on, then press VCR/ DVD on the unit or VCR on the Remote so that the VHS indicator lights up on the front display panel. A Press POWER to turn off the unit, then press 8 STOP on the unit for more than 5 seconds. “3 CH” appears on the front display panel. B Press CH +/– on the Remote to select “– CH” (off), then press ENTER. NOTES: . You can obtain high-quality component video pictures. . If your TV is not stereo-capable, use the unit’s AUDIO OUTPUT connectors to connect to an audio amplifier for Hi-Fi stereo sound reproduction. . To operate the unit with your TV using the Component Video connection, set your TV to its AV mode. You can also use the TV/VCR button on the unit’s Remote to set JVC TV to the AV mode. For switching the TV’s mode, refer to the instruction manual of your television. . By using the component video connection, you can view the images in the progressive mode. For switching to the progressive mode, refer to “Scan Mode Set (DVD deck only)” (. pg. 15). EN 15 A A Turn on the unit. Scan Mode Set (DVD deck only) This unit supports the progressive scan system (eg. 480p*) as well as the conventional interlaced scan system (eg. 480i*). If your TV equipped with component video connectors supports the progressive video input, you can enjoy a high quality picture by setting the progressive scan mode to active. . Refer also to the instruction manuals supplied with your TV. . If your TV equipped w...