Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
MOUNT THE PUSHBUTTON AT LEAST 5 FT FROM THE FLOOR, OUT OF REACH OF CHILDREN. 106495B2 Figure 2 Signal Sent Indicator Battery Hatch Mounting Screw Hole Keypress Indicator Mounting Holes PROGRAMMING INSTRUCTIONS 1 2 3 4 # # 1 1 2 1 3 1 2 1 3 2 # Default PIN DIP Switch Settings from Transmitter + 0 - 1 2 3 4 5 6 7 8 9 Figure 3 PROGRAMMING INSTRUCTIONS Write the settings of your transmitter DIP switches into the Transmitter Code table: 1 2 3 4 # # 1 # Factory Default Your Transmitter Code STEP 3: Now program your keypad: 1. Press the ON/Reset button. 2. Enter the Factory Default PIN, 1, 2, 3, 4 3. Press key # 4. Press key # The Transmitter Code is now programmed into your Keypad. Dual or Triple Button Transmitter If your gate or door operator has a two or three button transmitter: STEP 1: Locate your transmitter and open the coding hatch. You will see a coding switch block with numbers from 1 to 8 The possible setting for each switch is either “+”, “0” or “-”. Translate these settings into a numeric code: + = 1 0 = 2 - = 3 STEP 2: Copy the transmitter code as it is currently set into the table below. For example, Figure 4 shows DIP switch settings of: +, 0, +, -, +, 0, +, The numeric equivalent is: 1, 2, 1, 3, 1, 2, 1, 3 5. Press key 1 6. Enter the Transmitter Code you filled in above 7. Press key # + 0 - 1 2 3 4 5 6 7 8 Example Table: 1234 ## 1 Primary PIN DIP Switch Settings from Transmitter Figure 4 # 1 21 31 21 3 Transmitter Button Code Write the settings of your transmitter DIP switches into the Transmitter Code table: Note the “Transmitter Button Code” box in the table below. You must also program the code for the specific transmitter button that you will use to open the gate or door. On a two button transmitter, the left button code is 1, and right button code is 2. On a three button transmitter the left button code is 1, the middle button code is 2, and the right button code is 3. If you are programming the keypad so that the left transmitter button opens the gate or door, you will enter a 1 in the “Transmitter Button Code” box below. 1 2 3 4 # # 1 # Factory Default Your Transmitter Code Transmitter Button Code STEP 3: Now program your keypad: 5. Press key 1 1. Press the ON/Reset button. 6. Enter the Transmitter Code you filled in above 2. Enter the Factory Default PIN, 1, 2, 3, 4 7. Enter the Transmitter Button Code you filled in above 3. Press key # 8. Press key # 4. Press key # The Transmitter Code is now programmed into your Keypad. 3 PROGRAMMING INSTRUCTIONS #1 2 3 4 # 1 Factory Default Pin Pin No. New Pin Repeat New Pin PROGRAMMING YOUR PIN It is now time to change the factory default PIN of 1, 2, 3, 4 to your own private PIN. STEP 1: Begin by filling out the table above. You may program up to four PIN Codes. The PIN No. entry represents the first, second, third and fourth PIN you are choosing to program. In the table above, PIN No. 1 represents the required entry for programming the first PIN you have selected. This first PIN will be your Primary PIN. A sample block has been filled out below. In this example the PRIMARY PIN is the factory preset code. The PIN No. 3 indicates the third code in your system (this may be valid even if you do not have a second code). New PIN Code 5127 is an example representing the new PIN Code you have chosen. NOTE: DO NOT REVEAL YOUR PRIMARY PIN CODE. IT IS THE ONLY NUMBER WHICH CAN BE USED FOR PROGRAMMING AND IS YOUR INSURANCE AGAINST ANYONE REPROGRAMMING YOUR KEYPAD. #1 2 3 4 # 3 5 1 2 7 5 1 2 7 Factory Default Pin Pin No. New Pin Repeat New Pin STEP 2: Press the ON/RESET button and enter all of the characters in the sequence shown in the table at the top of the page. STEP 3: Check your new setting by entering your new PIN Code, OPERATING INSTRUCTIONS To operate your new wireless keypad press the RESET/ON key to light or reset your keypad. Enter your PIN followed by the * symbol and then your door umber. For example: ON/RESET 5 1 2 7 * 1 Activate Keypad Your PIN Door Number followed by * and the number of the door you wish to activate. The operator should respond. If not, repeat steps 5 and 6. Press the RESET/ON button should you press an incorrect key, and begin programming again. Your operator should be activated. If not, try again, making certain you are entering the correct PIN. If your operator is still not activated, a programming error may have been made. Repeat the programming steps outlined in the Programming Instructions section of this manual. Manufacturer’s Limited Warranty Allstar warrants its radio controls to be free from defect in material and workmanship for a period of one (1) year from the date of purchase. To obtain service, contact your dealer. To obtain service under this warranty the buyer must obtain authorization instructions for the return of any goods from Allstar before returning the goods. The goods must be returned with complete identification, with copy of proof-of-purchase, freight prepaid and in accordance with Allstar’s instructio...
Otros modelos de este manual:Puertas y ventanas - 104078 (297.83 kb)