Votos - , Puntuación media:
(
)
)
Fabricar: Lennox Hearth
Tamaño del archivo: 374.73 kb
Nombre del archivo: bc556ef7-9fe5-4f6e-9a84-c1b50e190c68.pdf
Idioma del manual:
El documento se está cargando, por favor, espere
 |
El documento se está cargando, por favor, espere
Resumen del manual
Screen Face [Complete] (A) 2 ea. Upper Brackets w/Screws (B) 2 ea. 1/4”-20 Lower Face Mounting Screws (C) 6 ea. #10 Washers 6 ea. 10-24 Hex Nuts 1 ea. Instruction Sheet Cat. No. Model Description 75382 SCREENF-30 Screen Face, Double Door, Black Figure 1 - Kit Contents TOOLS NEEDED: Phillips Head Screwdriver 3/8” Socket or Nut Driver 5/32” Allen Wrench or T-Handle Wrench GENERAL iNFORMATiON If you encounter any problems, need clarification of these instructions or are not qualified to properly install this kit, contact you local distributor or dealer. Read this instruction sheet in its entirety before beginning the installation. All of these parts may scratch and bend, great care should be used in handling them. ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION AND OPERATION MANUAL PROVIDED WITH THE APPLIANCE APPLY TO THESE INSTRUCTIONS. TURN OFF THE FIREPLACE AND ALLOW IT TO COMPLETELY COOL BEFORE PROCEEDING. INSTALLATION INSTRUCTIONS Step 1. Using a 5/32” allen wrench, remove the lower face mounting brackets from the unit and reverse their locations left to right (see Figure2). Re-attach the brackets (see Figure 3) using the existing 10-24 screws. You will need to reverse the speed nuts so that the flat side is toward the center of the fireplace. The outside dimension between the brackets should be 28 inches. Figure 2 Right bracket to left side of fireplace. NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE 1 Figure 3 Step 2. Using a 3/8” socket or nut driver, attach the two upper mounting brackets to the six studs (three on each side - indicated by arrows in Figure 5) near the top, using the six #10 washers and 10-24 hex nuts provided. The square notch should be to the bottom of the face (see Figure 4). 1/4" Screw With Push Nut (The push nut holds the screw in place when installing face) Figure 4 - Upper Mounting Bracket Figure 5 - Install Upper Mounting Brackets Step 3. Remove the screen doors from the face by gently lifting up and out of their hinges. Check to make sure the washers that separate the two halves of the hinge have not fallen off. Set the screen doors aside. Step 4. Using a phillips screwdriver (through upper grill opening) attach the screen face to the fireplace starting with the upper brackets. Screw the upper brackets in part way only, you will tighten them in step 6. Step 5. Open the lower door on the screen face and thread the two 1/4”-20 phillips head screws (provided) through the lower hinge mounts into the speed nuts on lower face brackets, attached to the fireplace (see Figure 6). Step 6. Adjust the alignment and depth of the screen face until it sits flush with the wall and tighten all four mounting screws. Step 7. Finish the installation by putting the screen doors back on their hinges (check to make sure the was hers are in place). This completes the screen face Installation. Figure 6 - Lower Hinge Mounts Figure 7 - Completed Installation NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE Lennox reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local distributor for fireplace code information. Printed in U.S.A. © 2008 Lennox Hearth Products 2 P/N 775,288M REV. A 10/2008 Lennox Hearth Products 1110 West Taft Avenue • Orange, CA 92865...