Votos - 4, Puntuación media: 4.3
(
)
)
|
Resumen del manual
. Output (free voltage contact), 3A@ 125Vac or 30Vdc ♦ Case Material: ABS (UL94V0) ♦ Operating Temperature:-20~+70°C ♦ Ambient Humidity:0~95% relative humidity noncondensing ♦ Visual Signals: ■ Green: Power on ■ Red: Relay activated ■ Yellow: Program Mode ' Lock-out ♦ Factory Master Code: 1234 ♦ Invalid PIN Lockout: System will shut down 60 seconds while 6 times of incorrectly password attempted. ♦ Relay Activation Time: (*20) ■ Pulse mode : 1~99 seconds (01~99) ■ Latching mode (00) ♦ EPROM: Non-volatile memory, System will retain all programs and codes after a total loss of power. ♦ User PINs: (*01~*10) It is possible to program 10 different user PIN codes. 3. Program Instruction: ♦ Enter Program Mode: 1. Enter the master code twice (Factory master is r 1234 j ) ^•2 beeps and the Yellow LED will light up. ^ you are now in the "programming mode". 2. Note: After 60 seconds if you have not entered any codes or data, the system will automatically exit from the programming mode. After 6 wrong attempts at the master code the lockout facility will operate. ♦ Exiting from the program mode: 1. Press r#j to exit from the programming mode. Copyright Gianni Industries, Inc. All Rights Reserved. PMUDG5 Ver. B Publish:2009.06.15 Page: 1/ 3 E MW I GIANNI INDUSTRIES> fNC. 2. Note: After 60 seconds if you have not entered any codes or data, the system will automatically exit from the programming mode. After 6 wrong attempts at the master code the lockout facility will operate. ♦ To Enter a User Code : Enter the Programming mode 1. Enter the slot position code r*01~*10j ^-???? (user code 4 digit) ^ (beep) ^enrolled^ Press # to exit from the programming mode, or program other operating. 2. Note: The codes"0000","1234" or master code are not be used for PIN code. ♦ To Program Relocking Timer (relay): Enter the Programming mode 1. Press r*20j Followed by the number of seconds the relay should open^ r05j =5 seconds (01 ~99 = seconds) ^ (beep) ^enrolled ^ Press r#j to exit from the programming mode, or program other operating. 2. Enter r00 j Sets the relay to latching mode. (Correct code entered opens the relay, and the relay stays open until the correct code is entered again). ♦ To Delete a User Code : Enter the Programming mode^ Press the slot position code of your choice to delete (example "06") ^Press r*06j ^ r0000j ^ (beep) ^delete^Press r#j to exit from the programming mode, or programming other operating. ♦ To Change the Master codes: Enter the Programming mode, Enter r*00 j Followed by the new 4 digit master code^ (beep) ^enrolled^Enter r#j to exit from the programming mode, or program other operating. 4. Wiring diagram: Contact door reed switch Power Supply_ FAIL-SAFE LOCKING DEVICE □ V This reed switch is used to reset the re-locking time to 0 second when the door is moved. (Using N.O. contact in case of door closed, changeover to N.C. When door is moved) 12Vdc + Power _ Supply Tamper switch contact output (free voltage contact) V O Buzzer o o Tamper Switch NO (Fail-secure locks) Com NC (Fail-safe locks) P B REED REED + i Master Code resetting(2-3) to Factory Code"1234” O O Copyright Gianni Industries, Inc. All Rights Reserved. PMUDG5 Ver. B Publish:2009.06.15 Page: 2/ 3 GEM GIANNI INDUSTRIES!, INC. Note: The door strike must have a vartistor or a diode across the door strike terminals to suppress the back EMF of the strike - failure to do so will damage the relay contacts and electronic components. Warranty: The product is warranted against defects in material and workmanship while used in normal service for a period of 1 year from the date of sale to the original customer .GEM policy is one of continual development and improvement , therefore GEM reserves the right to change specifications without notice. Copyright Gianni Industries, Inc. All Rights Reserved. PMUDG5 Ver. B Publish:2009.06.15 Page: 3/ 3...