Votos - 4, Puntuación media: 3.3
(
)
)
|
Resumen del manual
It may connects to another reader and serve as a controller. DG-600H enables the beeper to go off whenever the keypad is pressed. A tamper switch is used to protect the reader from external damage by linking the relay to the alarming system. This model communicates in Wiegand protocol and has a set of 600 proximity cards set to 26~37-bit or 26-bit. (For DG-600E, proximity cards are set to either 26 or 44 bit.) It takes the reader 0.5 seconds at most to read a proximity card or 5-digit PIN code. The built-in non-volatile memory preserves the PINs for as long as 10 years. Even when the power fails, the stored PIN codes will not be washed away. Operating Voltage: 9VDC to 16VDC Current Draw: Average 50mA, Peak 100mA/12VDC Transmitting Frequency: 125 KHz, Memory Volume: 600 Proximity cards/tokens and PIN codes Read Range: Up to 10 cm (Depending on local installation conditions) Keyboard: 12 digits keypad (0~9, *, #) Input: Request-to-exit, door reed switch, auxiliary reader Relay rating: 2A MAX/30VDC, 0.4A/120VAC Invalid PIN Lock-out: The system will shut down for 60 seconds After the attempt to read the master or PIN cards has faiiled for over 8 times. (No beeper signal when pressing on the keypad) I Relocking timer: Strike Time: 1~99 seconds (adjustable) Strike mode: Access Timer or Latch Alarm Function: Door Held Open Alarm: 10~99 Door Forced Alarm Panel Temper Alarm I Auxiliary Reader Format: Wiegand 44 or 26-bit only format (adjustable), hexadecimal (Em 64-bit standard R/O or compatible) Case Material: ABS (UL94V0) Color: Dark gray/ Beige White Operating Temperature: -20~+70°C Ambient Humidity: 5~95% relative humidity (noncondensing) Visual Signals:3 LED display with audible Indication (Red/Yellow/Green) EMC: Meet CE requirement EMC: Meet CE requirement Unit: mm y Warranty The product is warranted against defects in material and workmanship while used in normal service for a period of 1 year from the date of sale to the original customer. The GEM policy is one of continual development and improvement; therefore GEM reserves the right to change specifications without notice. Copyright © Gianni Industries, Inc. All rights reserved DM-CA-DG-600H Ver. E Published on 2010.12.20 GIANNI INDUSTRIES, INC. No. 13, Zhongxing Rd., Tucheng Dist., New Taipei City 236,Taiwan (R.O.C.) Tel: 886-2 2267 7986 / Fax: 886-2 2267 9876 E-Mail: inquiry@gianni.com.tw Website: gianni.tw GEM DG-600H Stand-alone Proximity Reader j Auxiliary reader The auxiliary reader must not be further than 50 meters from the DG-600H. Also this reader should be nearer than 60 centimeters, to avoid disturbance. The suggested wire gauge is #22~26 AWG. Split of units for DG-600H and auxiliary reader in ranging up to 50 M bring out the friendly system device for low cost but high security with anti-tampering as well as convenience and reliability. GEMPROX-H 125 KHz,Wiegand 26~37-bit format output Size:88(L) X 44(W)X16(D)mm j Connecting Diagram Copyright Gianni industries, inc. All rights reserved. DM-CA-DG-600H Ver. E Published on 2010.12.20 GIANNI INDUSTRIES, INC. No. 13, Zhongxing Rd., Tucheng Dist., New Taipei City 236,Taiwan (R.O.C.) Tel: 886-2 2267 7986 / Fax: 886-2 2267 9876 E-Mail: inquiry@gianni.com.tw Website: gianni.tw...