Votos - 3, Puntuación media: 4.7
(
)
)
|
Resumen del manual
1. With the cover face down hold the front cover while sliding the back plate to the left. 2. Using your finger gently pry up on the back cover plate. The back plate with the paper product label should come away easily. Chime Tune Setting The following instructions explain how to change the tune on the wired chime. 1. Remove the chime cover and locate the two 3 position dip switches shown below. 2. Select the desired chime sound from the table below. Chime Sound Table Position 1 2 3 Westminster OFF OFF ON Ding Dong OFF ON OFF Knock ON OFF OFF Bronze Chime OFF ON ON Cuckoo Clock ON OFF ON Foghorn ON ON OFF Gong ON ON ON ON: Switch On (up) OFF: Switch Off (down) WARNING: Do not exceed 16VAC input to the chime. Installation 1. Remove the cover from the old door chime, disconnect the transformer and pushbutton wires (label them for reference). Remove the old chime. 2. Install new chime a. Remove the front cover from the chime. b. Pull the pushbutton and transformer wires through the slot in the base of chime. c. Mark the 4 holes using the base as a template with the arrow pointing up. d. If using the screw anchors, drill 4 - 5/32”holes and insert the plastic screw anchors. Otherwise drill a 3/64” pilot hole for the screws. e. Mount the chime base using the 4x25mm screws. f. Attach the two wires from each pushbutton as shown in the wiring diagram. For each push button, one wire should be connected to the “Common” screw and one wire should be connected to the “Front” or “Rear” screw. g. Attach the wires from the chime transformer to the “transformer connections” as shown in the wiring diagram. (There is no polarity requirement). h. Slide the front cover on the back plate of the chime. Wiring Diagram For technical support contact Jasco Products Company at 1-800-654-8483 or Made in China Hecho en China is a trademark of General Electric Company and is used under license to Jasco Products Company LLC, 10 E. Memorial Road, Oklahoma City, OK 73114. Rev. 08-13-08 19214-2 Front Door Dip Switch Rear Door Dip Switch Chime Rear Door Button Front Door Button Wired Chime Installation Instructions for Wired Chime Power Requirement: 16VAC @ 180mA maximum Included hardware: (1) Chime (4) Plastic screw anchors (4) 4x25mm screws (for anchors) Required Tools: Wire stripper/cutter, small flat blade screwdriver, Phillips screwdriver, drill, and drill bit (5/32”) Removing Front Cover The following instructions explain how to remove the front cover of the wired chime. 1. With the cover face down hold the front cover while sliding the back plate to the left. 2. Using your finger gently pry up on the back cover plate. The back plate with the paper product label should come away easily. Chime Tune Setting The following instructions explain how to change the tune on the wired chime. 1. Remove the chime cover and locate the two 3 position dip switches shown below. 2. Select the desired chime sound from the table below. Chime Sound Table Position 1 2 3 Westminster OFF OFF ON Ding Dong OFF ON OFF Knock ON OFF OFF Bronze Chime OFF ON ON Cuckoo Clock ON OFF ON Foghorn ON ON OFF Gong ON ON ON ON: Switch On (up) OFF: Switch Off (down) WARNING: Do not exceed 16VAC input to the chime. Installation 1. Remove the cover from the old door chime, disconnect the transformer and pushbutton wires (label them for reference). Remove the old chime. 2. Install new chime a. Remove the front cover from the chime. b. Pull the pushbutton and transformer wires through the slot in the base of chime. c. Mark the 4 holes using the base as a template with the arrow pointing up. d. If using the screw anchors, drill 4 - 5/32”holes and insert the plastic screw anchors. Otherwise drill a 3/64” pilot hole for the screws. e. Mount the chime base using the 4x25mm screws. f. Attach the two wires from each pushbutton as shown in the wiring diagram. For each push button, one wire should be connected to the “Common” screw and one wire should be connected to the “Front” or “Rear” screw. g. Attach the wires from the chime transformer to the “transformer connections” as shown in the wiring diagram. (There is no polarity requirement). h. Slide the front cover on the back plate of the chime. Wiring Diagram For technical support contact Jasco Products Company at 1-800-654-8483 or Made in China Hecho en China is a trademark of General Electric Company and is used under license to Jasco Products Company LLC, 10 E. Memorial Road, Oklahoma City, OK 73114. Rev. 08-13-08 19214-2 Front Door Dip Switch Rear Door Dip Switch Chime Rear Door Button Front Door Button ...