Votos - 4, Puntuación media: 3.3
(
)
)
|
Resumen del manual
It is therefore strongly recommended that the equipment is set to use DTMF signalling for access to public or private emergency services. DTMF signalling also provides faster call set up. This CE Marking shows compliance of this equipment with Directive 73/23/EEC and Directive 89/336/EEC (as amended by Directive 92/31/EEC), both as amended by Directive 93/68/EEC. Canon Inc. /Canon Europa N.V. Copyright Copyright r1997 by Canon, Inc. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual, or otherwise, without the prior written permission of Canon, Inc. Trademarks Canontis a registered trademark, and UHQTM is a trademark of Canon Inc. Other brand and product names may be trademarks or registered trademarks of their respective companies. As an Energy Star Partner, Canon has determined that the FAX-L250 meets the Energy Star guidelines for energy efficiency. EPA POLLUTION PREVENTER NOTICE FOR CONNECTION TO TELECOMMUNICATION SYSTEMS IN THE UNITED KINGDOM AND THE REPUBLIC OF IRELAND Approval Number XXXXXX (UK) Your Canon FAX-L250 has been approved against the requirements of NTR3 for use in the UK and complies with the requirements of 91/263 EEC. The CE mark is applied in respect of the requirements of 72/23 EEC and 89/336 EEC. (UK) It is intended for connection to analogue two wire public telecommunication networks. Connect the supplied cable to this socket first, then to the telephone line. There are two auxiliary sockets to which equipment approved for direct connection to the network may be connected. If required, a suitable adaptor, approved under Approval Number NS/G/23/L/100005 for connections between the fax machine and any piece of approved telecommunications apparatus, is available from your Canon supplier. (UK) This socket is intended for connection of a telephone, the optional handset, an answering machine or similar device. Voltage and current available at these sockets is determined by the network to which the line cable is connected. They will not normally exceed the limits for TNV as described in EN60950. Canon recommend that any additional equipment connected in the installation is connected to one of these sockets. Do not connect additional equipment through parallel sockets elsewhere on the telephone line. This equipment is not intended or recommended for making calls to emergency services. EMC Directive This equipment has been tested in a typical system to comply with the technical requirements of the EMC directive. Use of a shielded cable is necessary to comply with the technical requirements of the EMC Directive. For your safety (Australia only) To ensure safe operation the three-pin plug supplied must be inserted only into a standard three-pin power point which is effectively earthed through the normal household wiring. Extension cords used with the equipment must be three-core and be correctly wired to provide connection to earth. Wrongly wired extension cords are a major cause of fatalities. The power point shall be located near the equipment and shall be easily accessible. The fact that the equipment operates satisfactorily does not imply that the power point is earthed and the installation is completely safe. For your safety, if in any doubt about the effective earthing of the power point, consult a qualified electrician. Caution (New Zealand only) 1. This equipment may not necessarily provide for the effective hand-over of a call to or from a telephone connected to the same line. 2. The operation of this equipment on the same line as telephone or other equipment with audible warning devices or automatic ring detectors will give rise to bell tinkle or noise and may cause false tripping of the ring detector. Should such problems occur, the user is not to contact Telecom faults service. 3. Should this equipment become physically damaged, disconnect immediately from the Telecom connection and power source and contact your nearest service agent. 4. To relocate this equipment please. 1) Disconnect the equipment from the Telecom connection. 2) Disconnect the equipment from the power source. 3) Reconnect the equipment to the power source. 4) Reconnect the equipment to the Telecom connection. 5. If the supply cord of this equipment is damaged, it must be replaced by the special cord (Parts No.: HH2-1910). 6. Not all standard telephones will respond to incoming ringing when connected to the extension socket. Safety Information Laser Safety Laser radiation could be hazardous to the human body. For this reason, laser radiation emitted inside this fax is hermetically sealed within the protective housing and external cover. In the normal operation of the product by the user, no radiation can leak from the machine. This fax is classified as Class 1 laser product under IEC 825, and as for the ...